Assessments - 4, GPA: 4.5
(
)
)
|
Facilidade de uso
@ 0 Level meter mode select switch • The position of this switch will determine the Level Meter mode. In the “MASTER” position, the meter will detail the out level of the left and right channels. In the “PGM 1/2” position, the left side of the meter will indicate monaural level of the PGM 1 and the right side of the meter will indicate monaural level of the PGM 2. @ 1 Channel Fader • Controls the channel output level. @ 2 Level meter • The dual LED's indicators are used to detail either the master output level, a combination of the master output level and the CUE signal level, or the PGM1/2 monaural level. @ 3 Crossfader • Fades the overall mixer output between channels 1 and 2. (2) Rear panel @ 4 Power operation • Selects power “ON” or “OFF”. NOTE: Whenever the power switch is in the AC adaptor is still connected on voltage. Please be sure to unplug the cord you don’t use for along time. @ 5 BALANCED MASTER OUT jacks • These 1/4” TRS jacks provide a balanced line level output. • Connect these jacks to the balanced analog input jacks on an amplifier or console. • Pin layout: Tip=Hot Ring=Cold Sleeve=GND @ 6 EFFECT LOOP SEND/RETURN jacks • These 1/4” TS stereo jacks allow external processing of the program signal. • When connect monaural type effect processor, use Lch input and output. @ 7 MIC BALANCED INPUT jack • Accepts an balanced microphone with 1/4” TRS mono jacks. • Pin layout: Tip=Hot Ring=Cold Sleeve=GND @ 8 MIC EFFECT LOOP jack • These 1/4” TRS jack allow external processing of the program signal. • Pin layout: Tip=SEND Ring=RETURN Sleeve=GND @ 9 PGM1, 2 FADER output jacks • Connect these jacks to the FADER input jacks of DN-S3000, DN-S5000, DN-S1000 and etc. using the 3.5mm stereo mini cord. # 0 Phono ground screw (GND) • This screws provide a place to connect the ground wire from a turntable. • This terminal is exclusively for a turntable ground and not a safety earth ground. # 1 PHONO1, 2 / LINE1, 3 switches (LN / PH) • These switches change the input from PHONO to a LINE level input. • These switches set a LINE level input when turntable is not connected. NOTE: Always be sure main power is shut off before change the position of the Line Level Selector Switch. # 2 PHONO1, 2 / LINE1, • These stereo pairs of unbalanced inputs for a PHONO (RIAA) stage (MM) cartridges or a LINE stage device, such as a CD player. # 3 LINE2, 4 input jacks • These stereo pairs of unbalanced RCA jacks inputs for any line level device. # 4 AUX INPUT jacks • This stereo pair of RCA jacks provides an unbalanced line level input with independent top panel AUX INPUT control. • This input is mixed after the Crossfader and EFFECT LOOP. # 5 BOOTH OUT jacks • This stereo pair of RCA jacks is the same as the MASTER output with independent BOOTH LEVEL control. • This output may be for recording, booth/zone monitoring, or for connecting to another mixer. # 6 UNBALANCED MASTER OUT jacks • This stereo pair of RCA jacks provides an unbalanced line level output. • Connect these jacks to the unbalanced analog input jacks on an amplifier or console. # 7 AC IN • Input connection for the included AC adaptor. NOTE: Use specified attached AC adaptor only. (3) Front panel # 8 CH 1/2 FADER START switches • Use this to switch the Channel function ON and OFF. # 9 CROSSFADER START A, B switches • Use this to switch the Crossader Start ON and OFF. $ 0 HEADPHONE output jack • Accept 1/4” stereo headphone plugs. $ 1 CH 1/2 FADER CONTOUR adjustment • Adjusts the curve of the CH1/2 faders between fast, normal , or slow fade. $ 2 CH 1/2 FADER REVERSE switch • Reverses the direction of each respective input CH1/2 fader. $ 3 CROSSFADER CONTOUR adjustment • Adjusts the shape of the crossfader curve from a fast cut for scratching or to a slow fade for mixing. $ 4 CROSSFADER REVERSE switch • Reverses the direction of the crossfader. 7 ENGLISH L R L R R L R L R L R L R L R L R L R L DN-X300 AA-26 AA-27 DP-DJ151 Digital Quartz ANTI-SKATING 765432 10 ON SLOW BRAKE OFF POWER START /STOP 45 0 1 2 3 4 33 78 +12 0 -12 KEY ADJUST PITCH DP-DJ151 Digital Quartz ANTI-SKATING 76543210 ON SLOW BRAKE OFF POWER START /STOP 45 0 1 2 3 4 33 78 +12 0 -12 KEY ADJUST PITCH 3 CONNECTIONS Refer to the connection diagram below. 1. Make certain AC power is off while making connections. 2. Quality cables make a big difference in fidelity and punch. Use high-quality, audio cables. 3. Do not use excessively long cables. Be sure plugs and jacks are securely fastened. Loose connections cause hum, noise, or intermittents that could damage your speakers. 4. Connect all stereo input sources. Then connect any effects into the stereo effect, if used. Connect your microphone(s) and monitor headphones. Make sure all faders are at “zero” and the unit is off. Take care to connect only one cable at a time. pay attention to L and R position of jacks, on both the DN-X300 and outboard gear. 5. Connect the stereo outputs to the power amplifier(s) and/or tape deck(s) and/or MD recorder(s) and/or CD r...