Assessments - 1, GPA: 4
(
)
)
|
Facilidade de uso
Additional Regulators and Controls Since the air tank pressure is usually greater than that which is needed, a separate regulator is usually employed to control the air pressure ahead of any individual air driven device. Break-in Procedures Serious damage may result if the following break- in instructions are not closely followed. This procedure is required: 1. Before the air compressor is put into service. (Before the hose is installed.) 2. When the check valve is replaced. 3. When a complete compressor pump is replaced. a. Set the pressure switch lever to the "OFF" position. b. Plug the power cord into the correct branch circuit receptacle. c. Turn the regulator clockwise opening it fully, to prevent air pressure build-up in the tank. d. Move the pressure switch lever to "ON/AUTO". The compressor will start. e. Run the compressor for 15 minutes. Make sure the regulator is open and there is no tank pressure buildup. f. After 15 minutes, close the regulator by turning it counterclockwise. The air receiver will fill to cut-out pressure and the motor will stop. The compressor is now ready for use. 8 — ENG INSTALLATION AND BREAK-IN PROCEDURES (cont'd) Wiring Instructions - Stationary Wiring must be such that full motor nameplate voltage plus or (Permanently Mounted) Compressors minus 10% is available at the motor terminals during starting. Refer to local codes for recommended wire sizes for correct wire If your compressor is not equipped with a plug-in type power size and maximum wire run; undersize wire causes high amp cord, perform electrical wiring according to the following in- draw and overheating to the motor. structions: RISK OF ELECTRICAL SHOCK. IMPROPER ELECTRICAL GROUNDING CAN RESULT IN ELECTRICAL SHOCK. WIRING FOR THIS UNIT SHOULD BE DONE BY A LICENSED ELECTRICIAN IN ACCORDANCE WITH NATIONAL AND LOCAL CODES AND ORDINANCES. Install the compressor as close to the main power supply as possible. This practice will avoid using long lengths of electrical wiring for the power supply which can cause power loss to the motor. When connecting wires, make sure that : 1. The amperage rating of the electrical box is adequate. Refer to the Specification Chart in the Parts List Manual for your compressor. 2. The supply line has the same electrical characteristics (voltage, cycle, phase) as the motor. OPERATING Daily Start-Up Checklist 1. Before attaching air hose or accessories, make sure the ON/AUTO lever is set to “OFF” and the air regulator or globe valve is closed. 2. Attach hose and accessories. TOO MUCH AIR PRESSURE CAUSES A HAZARDOUS RISK OF BURSTING. CHECK THE MANUFACTURER'S MAXIMUM PRESSURE RATING FOR AIR TOOLS AND ACCESSORIES. THE REGULATOR OUTLET PRESSURE MUST NEVER EXCEED THE MAXIMUM PRESSURE RATING. Compressed air from the outfit may contain water condensation. Do not spray unfiltered air at an item that could be damaged. Some air operated tools or devices may require filtered air. Read the instructions for the air tool or device. 3. Check the manufacturer’s maximum pressure rating for air tools and accessories.The regulator outlet pressure must never exceed the maximum pressure rating. If your compressor is not supplied with a regulator with gauge, install one before using accessories. 4. Turn the ON/AUTO lever to “AUTO” and allow tank pressure to build. Motor will stop when tank pressure reaches “cut-out” pressure. Electrical wiring must be located away from hot surfaces such as manifold assembly, compressor outlet tubes, heads, or cylinders. Grounding Instructions - Stationary (permanently mounted) compressors This product should be connected to a grounded, metallic, permanent wiring system, or an equipment-grounding terminal or lead on the product. This unit was not designed to operate on 208 volts. PROCEDURES 5. Open the regulator by turning it clockwise. Adjust the regulator to the correct pressure setting. Your compressor is ready for use. 6. Always operate the air compressor in well-ventilated areas; free of gasoline or other solvent vapors. Do not operate the compressor near the spray area. When you are finished: 7. Set the “ON/AUTO” lever to “OFF”. 8. Turn the regulator counterclockwise and set the outlet pressure to zero. 9. Remove the air tool or accessory. 10. Open the regulator and allow the air to slowly bleed from the tank. Close the regulator when tank pressure is approximately 20 psi. 11. Drain water from air tank by opening drain valve on bottom of tank. WATER WILL CONDENSE IN THE AIR TANK. IF NOT DRAINED, WATER WILL CORRODE AND WEAKEN THE AIR TANK CAUSING A RISK OF AIR TANK RUPTURE. 12. After the water has been drained, close the drain valve. The air compressor can now be stored. NOTE If drain valve is plugged, release all air pressure. The valve can then be removed, cleaned, then reinstalled. 9 — ENG MAINTENANCE UNIT CYCLES AUTOMATICALLY WHEN POWER IS ON. WHEN DOING MAINTENANCE, YOU MAY BE EXPOSED TO VOLTAGE SOURCES, COMPRESSED AIR OR MOVING PARTS. PERSONAL INJURIES CAN OCCUR. BEFO...