Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
Check with a qualified electrician or 4. service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded. Use only 3-wire extension cords that 5. have 3-prong grounding plugs and 3-pole receptacles that accept the compressor’s plug. Repair or replace damaged or worn 6. cord immediately. 7. This compressor is intended for use on a circuit that has an outlet that looks like the one illustrated above in 125 V~ 3-Prong Plug and Outlet. The compressor has a grounding plug that looks like the plug illustrated above in 125 V~ 3-Prong Plug and Outlet. The outlet must be properly installed 8. and grounded in accordance with all codes and ordinances. Do not use an adapter to connect this 9. compressor to a different outlet. Double Insulated Compressors: Compressors with Two Prong Plugs To reduce the risk of electric shock, 1. double insulated equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Double insulated compressors may 2. be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Specifications Electrical Requirements 120 V~ / 60 Hz / 210 W (Load) / 4.5 A (Start Up) / 6.25 A (Peak) Three Prong Plug Air Tank Capacity 3 Gallons Pressure Range 70-100 PSI Air Flow Capacity .5 CFM @ 90 PSI / .7 CFM @ 40 PSI Accessories 25’ Coil Air Hose / Air Chuck Unpacking When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Product Overview Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. To prevent serious injury from accidental operation: Turn the Power Switch of the compressor to its “OFF” position and unplug the compressor from its electrical outlet before assembling or making any adjustments to the compressor. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Prior to using the Air Compressor, make sure to familiarize yourself with its basic features and methods of operation as described in this section: Power Switch (19): 1. The Power Switch turns the Air Compressor ON and OFF. When the Power Switch is in its ON position it allows the Air Compressor to automatically start up or shut down depending on the level of compressed air in the Air Compressor’s Tank (14). Safety Valve (3): 2. If the Air Compressor does not automatically shut down when the air pressure reaches the TOOL PRESSURE GAUGE (2A) Air Line Connection Point TOOL PRESSURE REGULATOR (6) TANK (14) POWER SWITCH (19) TANK PRESSURE GAUGE (2) Safety VALVE (3) Drain (9) factory preset level, the Safety Valve will automatically pop open to prevent over pressurization in the Tank (14). To operate the Safety Valve manually, pull the ring on the Safety Valve to relieve air pressure in the Tank. Tank Pressure Gauge (2): 3. The Tank Pressure Gauge measures the air pressure stored in the Tank (14), and is not adjustable by the operator. Tool Pressure Gauge (2A): 4. The Tool Pressure Gauge measures the air pressure being supplied to the tool being used. Tool Pressure Regulator (6): 5. The Tool Pressure Regulator allows you to adjust the air pressure (0 to 120 PSI) being supplied to the tool being used. Turn the Tool Pressure Regulator clockwise to increase the air pressure to the tool, and counterclockwise to decrease the air pressure. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Close the Drain (9) completely.1. Turn the Tool Pressure Regulator 2. (6) counterclockwise until it is fully closed. Pull the ring on the Safety Valve (3) 3. to check that it operates properly. Attach the Air Hose (20) to the air 4. outlet on the Regulator (6). Connect the other end of the air hose to the air inlet of the tool. Other components, such as a connector and quick coupler, will make operation more efficient, but are not required. Note: If inflating tires or other objects, connect the Air Hose (20) to the Inflation Chuck (21). Do not overinflate any object. Plug the Power Cord/Plug (7) into the 5. nearest 120 volt, grounded, electrical outlet. Turn the Power Switch (19) to its 6. AUTO or | position. Observe the Tank Pressure Gauge 7. (2), and allow the air pressure in the Tank (14) to build up to 70 PSI. Observe the Tool Pressure Gauge 8. (2A), while turning the Tool Pressure Regulator clockwise to increase pr...