Assessments - 5, GPA: 4.4
(
)
)
|
Facilidade de uso
Fluid Type The Pump is designed for use with water with a maximum temperature of 95° F (35°C). Do not use the pump for other fluids, especially not fuels, cleaning fluids, or other chemical products. Specifications Pump Applications Removes Clear Water Down to 1/8” of Surface Electrical Requirements 115 V~ / 60 Hz / 1/4 HP 2.6 A (Start) / 2.5 A (Run) Power Cord 18AWG X 3C - SJTW Maximum Capacity 1400 GPH (Approx. 23 GPM) Maximum Delivery Height 26.3 Ft. Discharge Size 1” Pipe with 3/4”-11.5 TPI Garden Hose Adapter Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Installation The submersible motor pump must be installed in a stationary position with either: A fixed pipeline ora. A flexible hose pipe.b. Please note! Do not install the pump by suspend1. ing it unsupported from its delivery pipe or power cord. The pump must be suspended from the handle or be placed on the bottom of the shaft. To ensure that the pump works properly, keep the bottom of the shaft free from sludge and dirt of all kinds. If the water level sinks too low, any 2. sludge in the shaft will dry out and stop the pump from starting. To help ensure the pump will start as required, check the pump regularly with start-up tests. The pump must be installed with an 3. automatic float switch (not included) to prevent running dry. Power Supply The pump is equipped with a shock-1. proof plug according to regulations. The pump is designed to be connected to 115 V~, 60 Hz safety socket. Make sure that the socket is suf2. ficiently secured and is in excellent condition. When the plug is inserted into the 3. socket the pump will be on standby. WARNING! If the power cord or plug is damaged, do not use the pump. The power cord or plug may only be repaired by a certified electrician. Areas of use This pump is designed for use as a 1. basement pump. When installed in a shaft, this pump provides some protection from basement flooding. This pump can also be used to trans2. fer water (e.g. household, farming, plumbing). Operation After reading these instructions, consider the following points before starting the pump: Verify that the pump rests on the floor 1. of the shaft, if it is not suspended by the handle. Verify that the delivery pipe is prop2. erly connected. Verify that the electrical connection is 3. 115 V~, 60 Hz. Verify that the electrical socket is in 4. good condition. Verify that water and moisture cannot 5. get near the power supply socket. Verify that the pump is installed so as 6. to prevent running dry. Maintenance To prevent serious injury from accidental operation: Unplug the Pump from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. If the pump is moved during operation, flush it out with clean water after every use. Quarterly Maintenance The below maintenance must be performed at least once every 3 months under optimal conditions. For frequent use, or dirty areas, more frequent maintenance is required. Clean sludge and debris from the bot1. tom of the shaft. Rinse the housing off with clean wa2. ter. Clean fibers from inside the pump 3. housing with a pressure washer (not included). If the pump housing cannot be 4. cleaned from the outside, it must be thoroughly cleaned. Make sure the power cord is unplugged before maintenance. Dismantle the bottom part of the pump as follows: FIGURE BIMPELLER(14) FILTER(11) a. Remove the Filter (11) from the pump case. Clean the impeller with clean water.b. To prevent damage, do not rest the c. pump on the impeller or pry against the impeller. Reassemble in reverse order.d. Troubleshooting Problem Possible Causes Possible Solutions Pump runs, but will not deliver any water. Filter and/or impeller clogged.1. When starting, the pump water 2. height (1/8”) falls below the minimum water level. Low line voltage.3. Optional check valve stuck or 4. installed backwards. Remove filter. Clean out dirt and debris from 1. filter and impeller. Then replace Filter. There must be at least 1/8” deep water for the 2. Pump to operate properly. Consult with an electrician.3. Remove and examine check valve.4. Pump won’t start or run. Check power connections and 1. circuits/fuses. Water level too low.2. Filter and/or impeller clogged.3. Defective motor.4. Consult with an electrician.1. Allow water level to rise above 1/8”, or move 2. Pump to a lower location. Remove filter. Clean out dirt and debris from 3. filter and impeller. Then replace filter. Have a qualified service technician repair or 4. replace. Excessive noise or vibration. Worn bearings.1. Debris in impeller.2. Discharge garden hose 3. restricted. Have a qualified service technician repair or 1. replace. Remove filter. Clean impeller. Then replace 2. filter. Clean Pump and discharge garden hose.3. Pump starts and stops too frequently. Water temperat...