Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
The 1F59-13 thermostat has no indicator lights. 50 60 70 80 90 70 1F59-13 PRECAUTIONS If in doubt about whether your wiring is millivolt, line, or low voltage, have it inspected by a qualified heating and air conditioning contractor or a licensed electrician. Do not exceed the specification ratings. All wiring must conform to local and national electrical codes and ordinances. This control is a precision instrument, and should be handled carefully. Rough handling or distorting components could cause the control to malfunction. To prevent electrical shock and/or equipment damage, disconnect electric power to system at main fuse or circuit breaker box until installation is complete. CAUTION! Do not use on circuits exceeding 30 volts. Higher voltage will damage control and could cause shock or fire hazard. DO NOT USE this thermostat on heat pump systems that have a spark ignition gas or fossil fuel second stage heat source. WARNING! SPECIFICATIONS ELECTRICAL DATA THERMAL DATA Electrical Rating: Temperature Range: 40°F to 90°F (4°C to 32°C) 18 to 30 VAC, 50/60 Hz Rated Differential: Stage 1 heat – 1.3°F (max.) 0.01 to 1.5 amps (load per terminal) Stage 2 heat – 0.9°F (max.) 2.5 amps max. total load (all terminals combined) Cooling – 1.3°F (max.) STAGING DATA DIMENSIONS Up to two heating stages 3.5” H x 5.5” w x 1.25” D One cooling stage WHITE-RODGERS DIVISION PART NO. 37-5780A EMERSON ELECTRIC CO. Printed in U.S.A. 9797 REAVIS ROAD ST. LOUIS, MISSOURI 63123-5398 INSTALLATION SELECT THERMOSTAT LOCATION Proper location insures that the thermostat will provide a comfortable home temperature. Observe the following general rules when selecting a location: 1. Locate thermostat about 5 ft. above the floor. 2. Install thermostat on a partitioning wall, not on an outside wall. 3. Never expose thermostat to direct light from lamps, sun, fireplaces or any temperature radiating equipment. 4. Avoid locations close to windows, adjoining outside walls, or doors that lead outside. 5. Avoid locations close to air registers or in the direct path of air from them. 6. Make sure there are no pipes or duct work in that part of the wall chosen for the thermostat location. 7. Never locate thermostat in a room that is warmer or cooler than the rest of the home, such as the kitchen. 8. Avoid locations with poor air circulation, such as behind doors or in alcoves. 9. The living or dining room is normally a good location, provided there is no cooking range or refrigerator on opposite side of wall. ROUTE WIRES TO LOCATION 1. If an old thermostat is being replaced and is in a satisfactory location, and the wiring appears to be in good condition, use existing wiring. If in doubt, re-wire. 2. If a new location is chosen or if this is a new installation, thermostat wire must first be run to the location selected. All wiring must conform with local and national electrical codes and ordinances. 3. Probe for obstructions in partition before drilling 1.2” hole in wall at selected location. Take up quarter round and drill a small guide hole for sighting (see fig. 1). From basement, drill 3.4” hole in partition floor next to guide hole. In houses without basements, drill 1.2” hole through ceiling and into partition from above (see fig. 1). 4. Through this hole drop a light chain, or 6” chain attached to a strong cord. Snag cord in basement with hooked wire. In houses without basements, drop cord through hole in ceiling and down partitioning; snag cord at the thermostat location. 5. Attach thermostat wire to cord and pull wire through hole in wall so that 6” of wire protrudes. ATTACH THERMOSTAT BASE TO WALL 1. Remove thermostat cover. Pull wires through opening near center of thermostat base and connect wires under terminal screws (see WIRE THERMOSTAT TO SYSTEM). 2. Push excess wire into wall and plug up hole with fire-resistant material, such as fiberglass insulation, to prevent drafts from affecting thermostat operation. 3. Place thermostat base over hole in wall for wires and mark mounting hole locations on wall. 4. Drill mounting holes. Approximately 5 feet from floor 1.2” hole for thermostat wire Stout cord with 6” chain attached Baseboard strip moulding 1.4” guide hole for sighting Quarter round removed 3.4” hole in floor of partition Hooked wire for snagging chain Figure 1. Routing thermostat wires 5. Fasten thermostat base loosely to wall using two mounting screws (see fig. 2). Place a level against bottom of base, adjust until level, and then tighten mounting screws to secure base (leveling is for appearance only and will not affect thermostat operation). If holes in wall are too large and do not allow you to tighten base snugly, use plastic screw anchors to secure base. Screw Mounting Hole Anchors Mounting Hole Figure 2. Mounting thermostat base to wall G O Y B O F CAUTION! Take care when securing and routing wires so they do not short to adjacent terminals or rear of thermostat. Shorted wires may result in personal injury and/or property d...