Assessments - , GPA:
(
)
)
Fabricante : Makita
Arquivo Tamanho: 4.68 mb
Arquivo Nome : MAC1200.pdf
Língua de Ensino: 
O documento está colocado, por favor, espere
 |
O documento está colocado, por favor, espere
Facilidade de uso
MAC1200 SPECIFICATION CHART Model No. MAC?200 , Horsepower 2 ;c* Displacement CFM 11.9 SCFM G2 40 psig 8.3 SCFM G2 9Opsig 6.1 Cut-In 100 PSI cut-out 125 PSI Bore 2 38" Stroke 1.35" Voltage-Single Phase 120 "Fusetron" Type T k + Fuse Type Amperage at Max. Pressure 15 amps Tank Size 4 Gallon U.L. & CUL Listed Minimum Circuit Requirement 15 AMPS I +Acircuit breaker is preferred. Use only afuse or circuit breaker that is the same rating as the branch circuit the air compressor is operated on. If the air compressor is connected to a circuit protected by fuses, use time delay fuses. NOTE: IMPORTANT: For identification of Parts, see Page 11 in this Read the Safety Guidelines and All Instructions Manual. Carefully Before Operating. ~ WMAC12QQA Rev. 1/14/97 TABLE OF CONTENTS Page SMETYGUIDELINES ............................................... 2 WARNING CHART................................................. 34 GLOSSARY ............................................................... 5 DUTYCYCLE ............................................................. 5 GENERAL INFORMATION ........................................ 5 ON-RECEIPTINSPECTION......................................... 5 DESCRIPTIONOFOPERATION.................................. 5 INSTALLATIONAND BREAK-IN pROCEDURES ....................................................... 6-7 Locationof Air Compressor .............................. 6 Lubrication and Oil ........................................... 6 Extension Cords ................................................ 6 Piping ............................................................... 6 Grounding Instructions ................................... 67 Additional Regulators & Controls ....................... 7 Break-in Procedures ........................................... 7 Page OPERATING PROCEDURES .................................. 7 Daily Start-up Checklist ..................................... 7 MAINTENANCE ...................................................... 8 Air Filter .Inspection and Replacement ............. 8 Safety Valve .Inspection................................... 8 Check Valve Replacement ................................. 8 Motor ................................................................. 8 STORAGE ............................................................... 9 TROUBLESHOOTING GUIDE ............................. 9-10 AIR COMPRESSOR DIAGRAM ............................. 11 AIR COMPRESSOR PARTS LIST .......................... 12 AIR COMPRESSOR PUMP DIAGRAM ..................13 AIR COMPRESSOR PUMP PARTS LIST ...............14 WARRANIY STATEMENT......................... Back Cover f r SAFETY GUIDELINES .DEFINITIONS i This manual contains informa- tion that is important for you to know and understand . This infor- mation relates to protectingYOUR SAFETYandPREVENTINGEQUIP- MENT PROBLEMS. To help you recognize this information. we use I II I symbols to the right. Please read the and pay to these sections . URGENT SAFETY INFORMATION .A HAZARD THAT WILL CAUSE SERIOUS INJURY OR LOSSOF LIFE. 1 AWARNING I IMPORTANT SAFETY INFORMATION .A HAZARD THAT MIGHT CAUSE SERIOUS INJURY OR LOSSOF LIFE. Information for preventing damage to equipment. 1 NOTE I I I Information that you should pay special attention to . 2 IMPORTANT SAFETY INSTRUCTIONS SAVFTHESF INSTRUCTION s* IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS :NJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING I=-I INSTRUCTIONS BEFORE USING THIS EQUIPMENT. - I HAZARD WHAT CAN HAPPEN HOW TO PREVENTIT 4ir Tank m THE FOLLOWING CONDITIONS COULD lead to a weakening of the RISK OF BURSTING tank,nd RESULT IN A VIOLENT 1 TANK EXPLOSION: 0 1. FAILURE TO PROPERLY DRAIN DRAIN TANK DAILY OR AFTER EACH condensed WATER FROM THE -USE. If tank develops a leak, replace it TANK, causina rust and thinning immediately with a new tank or new of the tank steel. compressor outfit. NEVER drill into, weld, or MAKE ANY repairs TO THE TANK. MODIFICATIONS TO THE TANK or its attachments. Never attempt to repair a damaged or leaking tank. Replace with a new tank 2. MODIFICATIONS or attempted 1 The tank is designed to withstand specific operating pressures. NEVER MAKE ADJUSTMENTS OR Pm SUBSTITUTIONS TO alter the FACTORY SET operating PRESSURES. Attachments and Accessories m -FOR essential CONTROL OF. AIR OF AIR TOOLS, spray guns, air operated PRESSURE, you must INSTALL A accessories, tires other EXCEEDING THE PRESSURE RATING PRESSURE REGULATOR .AND INFLATABLES CAN CAUSE THEM TO REGULATED AIR PRESSURE GAUGE to EXPLODE or fly apart, and could result the air outlet of your compressor. in serious injury. Follow the equipment manufacturers recommendation and never exceed the maximum allowable pressure rating of attachments. NEVER USE THE COMPRESSOR TO INFLATE SMALL LOW-PRESSURE OBJECTS SUCH AS CHILDREN’S TOYS. FOOTBALLS, BASKETBALLS. ETC. i Your AIR COMPRESSOR is powered b) Any ELECTRICAL WIRING OR electricity. Like anv other electricallv RE...