Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
pumping system, the following safety precautions must be observed at all times: 1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls and MANUAL the proper use of the equipment. 2. Follow all local electrical and safety codes as well as in the US, National Electrical Codes (NEC) and Occupational Safety and Health Act (OSHA). REMINDER: Keep your dated proof © 2004 Campbell Hausfeld/Scott For parts, product & service information IN611602AV 8/04 visit No. de Numero del Ref. Descripcion repuesto Ctd. No. de Numero del Ref. Descripcion repuesto Ctd. FP2051, FP2052 1 2 7 13 3 4 5 6 8 9 10 11 12 30 14 15 16 17 18 19 20 47 21 20 21 19 23 24 25 27 27 28 29 31 32 33 34 35 43 37 38 39 40 42 41 44 45 46 54 51 48 50 49 53 52 36 26 Sp Compresor de aire portatil Sirvase darnos la siguiente informacion: Puede escribirnos a: -Numero del modelo Campbell Hausfeld / Attn: Parts Department -Numero de Serie (de haberlo) 100 Production Drive -Descripcion y numero del repuesto segun la lista de repuestos Harrison, OH 45030 U.S.A. Para Ordenar Repuestos Sirvase Llamar al Distribuidor Mas Cercano a su Domicilio FP2051, FP2052 3 Installation (Continued) Do not use a grounding adapter with this product! 2. If repair or replacement of cord or plug is necessary, do not connect grounding wire to either flat blade terminal. The wire with insulation having an external surface that is green (with or without yellow stripes) is the grounding wire. Never connect green (or green and yellow) wire to a live terminal. 3. Check with a qualified electrician or serviceman if grounding instructions are not completely understood, or if in doubt as to whether product is properly grounded. Do not modify plug provided; if it will not fit outlet, have proper outlet installed by a qualified electrician. Overheating, short circuiting and fire damage will result from inadequate wiring, etc. WALL MOUNTING This compressor can be mounted to the wall for convenient storage. It can also be operated while in the hanging position. Before mounting, select a location at a wall stud or on a concrete surface. Make sure that the mounting area measures at least 24” x 30”. Hang compressor on a properly installed hanger sturdy enough to support compressor’s weight (approximately 25 pounds). Do not hang on peg board, wallboard, or any structure not suited to hold compressor’s weight. Mounting hanger bracket For mounting to a wood stud, the bracket has three holes in the center. These holes are located in between the two mounting hooks that attach to the back of the compressor. Use a stud finder to locate the center of the stud. ! WARNING ! CAUTION ! WARNING ! DANGER Use the screws provided to attach the bracket to the wall. Make sure to mount to the wood stud, not just to drywall. For mounting to a concrete surface, pre-drill holes in the concrete and insert the anchors that are provided. Align the holes in the bracket with the wall anchors and use the three screws provided to attach the bracket to the wall. Avoid mounting compressor to drywall or gypsum board unless screws are lagged into wood studs. Mounting air compressor to bracket There are three mounting hooks on the wall hanging bracket. On the back of the compressor shroud, there is an opening that serves as a handle. The two hooks on the top of the bracket fit in the handle opening on the compressor shroud. The remaining hook on the bottom of the bracket fits into the lower part of the compressor shroud, below the handle opening. HOSE STORAGE 1. Attach one of the threaded ends of recoil hose to air outlet on front of compressor. 2. Route recoil hose to side of tank where hose strap is located. 3. Loosen lower end of hose strap. 4. Slide as much of recoil as possible onto hose strap. 5. Reattach hose strap to compressor. Operation Definition of Terms Regulator - The regulator controls the amount of air pressure released at the hose outlet. ASME Safety Valve - This valve automatically releases air if the tank pressure exceeds the preset maximum. Handle - Designed to move the compressor. Drain Valve - This valve is located on the bottom of the tank. Use this valve to drain moisture from the tank daily to reduce the risk of corrosion. Reduce tank pressure below 10 psi, then drain moisture from tank daily to avoid tank corrosion. Drain moisture Gauge of Cord 18 18 16 14 14 12 12 10 10 Extension cords for 120V/2.5 Amp Unit Length of Cord (ft) 25 50 100 150 200 250 300 400 500 Figure 2 - Unit Identification Tank gauge Outlet gauge Safety valve On/off switch Regulator Portable Air Compr essor Operation (Continued) from tank by opening the drain valve located underneath the tank. LUBRICATION This is an oilless product and DOES NOT require lubrication to operate. BEFORE FIRST START-UP BREAK-IN PROCEDURE (Complete this procedure before using compressor for the first time. Once completed, it is not necessary to repeat.) 1. Turn regulator knob fully clo...
Este manual também é adequado para os modelos :equipamento de bombagem - FP2052 (1.25 mb)