Assessments - 2, GPA: 4 ( )

Fabricante : HP Arquivo Tamanho: 485.47 kb Arquivo Nome : Língua de Ensino:

1 Gallon Required) Turbine Oil 1 4K432 7.5 lbs./gal. 304 Impeller Locknut (3 PH only) AISI 300 series SS 1 13K6 – 338 Motor – 1 Phase, 115V Stainless Steel 1 118-121R 118-123R N/A N/A N/A N/A N/A 13.0 to 24.0 118-122R 118-124R 118-1212R 118-1213R 118-1233R 120-844R 120-845RMotor – 1 Phase, 230V Motor – 3 Phase, 230/460 V N/A 118-132R 118-1304R 118-134R 118-1323R N/A N/A Motor – 3 Phase, 200 V N/A 118-1314R 118-1316R 118-1316R 118-1335R N/A N/A Motor – 3 Phase, 200-230/460 V N/A N/A N/A N/A N/A 120-8425R 120-8425R 340 Bearing Housing Cast Iron 1 1K167 1K332 10.0 341 Motor Cover – 1 Phase Cast Iron1 1K207 1K207 1K208 1K208 1K208 1K208 1K208 20.0 Motor Cover – 3 Phase 1K208 351 Casing Gasket Composite 1 5K170 – 351A Discharge Flange Gasket Composite 1 5K150 – 357 Hex Nut –Edischarge flange AISI 300 series SS 2 13K99 358E Plug – motor cover 3.8" NPT Steel 1 6K3 – 371C Skt. Hd. Screw – brg. housing to motor cover AISI 300 series SS 4 13K210 – 371H Hex Screw – discharge flange AISI 300 series SS 2 13K153 – 372D Hex Screw – bearing housing to casing AISI 300 series SS 4 13K186 – 376 Capacitor (1 PH only) Start Varies 1 9K197 9K197 9K235 9K235 9K197 275469128 275470130 – Capacitor (1 PH only) Run N/A N/A N/A N/A N/A N/A 279342110 387 Mechanical Seal – standard Silicon Carbide 1 10K63 (John Crane Type 6) 10K71 – Mechanical Seal – optional Tungsten Carbide 1 10K30 (John Crane Type 21) 10K72 – 412M O-ring – motor cover Nitrile 1 4K252 – 436 Solid State Switch (motor) – 1 N/A 294612982 294811980 – 456 Power Cable – 1 See chart below – 457 Wire Nut 3 PH, 200/230 V Nylon Housing 4 9K145 – 6 9K145 –Wire Nut 3 PH, 460 V 458 Handle Assembly AISI 300 series SS 1 4K243 – 484B Strain Relief Assembly (power cable) 1 PH Varies 1 5K113 5K113 5K111 5K111 5K111 5K111 5K111 – 3 PH 1 N/A 5K111 – 528 Washer – discharge flange AISI 300 series SS 2 13K82 – Loctite #271 – 1 AL27121 – * Consult Factory Model 3887 Power Cables Description Type and AWG Size Standard length* Optional Lengths Wt. (lbs./5 ft.)20' 30' 50' 100' Power Cables 1 PH: 1.3 and 1.2 HP, 115 V; standard with plug, optional length with bare leads SJTOW – 16/3 9K165 9K214 9K215 N/A 0.5 1 PH: 1.3 and 1.2 HP, 230 V; standard with plug, optional length with bare leads SJTOW – 16/3 9K164 9K214 9K215 N/A 0.5 1 PH: 3.4 – 1HP, 230 V with bare leads STOW – 14/3 9K163 9K216 9K161 9K217 0.9 1 PH: 11.2 – 2 HP, 230 V with bare leads STOW – 14/3 9K266 9K267 9K268 9K269 0.9 3 PH: 1.2 – 2 HP, 208–230/460 V with bare leads STOW – 14/4 9K153 9K218 9K154 9K219 1.1 9K197 REF#615996 1 or 624751 1 MFD 110 VAC 9K235 REF#615996 2 189/227 MFD 110 VAC Typical 2" Slide Rail Installation Typical 2" Slide Rail Installation 13" 81.4" WALL BRACKET INTERMEDIARY WALL BRACKET FOR WET WELLS OVER 96" DEEP. LIFTING CABLE 12" 24" MIN. GUIDE RAILS 1" DIA. PIPE 61.4" MAX. COUPLING TOP PUMP BRACKET 32" MIN. SIMPLEX DISCHARGE QUICK DISCONNECT 11" VERTICAL PIPE NIPPLES CHECK VALVE 11" 36" 44" 221.2" MAX. BOTTOM PUMP BRACKET MIN. 11" BASE PLATE 11" 31.16" MIN. 32" 51.8" MIN. DUPLEX Typical Plumbing and Installation INFLUENT SERVICE POLE CONTROL PANEL GROUT SEAL HIGH LEVEL ALARM (OPTIONAL) FLOAT SWITCH 6" NORMAL OPERATION 3" MIN. SUBMERGENCE (MAINTENANCE ONLY) ALARM LIGHT (OPTIONAL) HINGED ACCESS DOOR WRENCH OPERATED VALVE VENT SLIDE RAIL VALVE OPERATING ROD DISCHARGE CHECK VALVE SLIDE RAIL GUIDE SIMPLEX INFLUENT SERVICE POLE CONTROL PANEL GROUT SEAL HIGH LEVEL ALARM (OPTIONAL) FLOAT SWITCH 6" NORMAL OPERATION 3" MIN. SUBMERGENCE (MAINTENANCE ONLY) ALARM LIGHT (OPTIONAL) HINGED ACCESS DOOR WRENCH OPERATED VALVE VENT SLIDE RAIL VALVE OPERATING ROD DISCHARGE CHECK VALVE SLIDE RAIL GUIDE DUPLEX Trouble Shooting FAILURE TO DISCONNECT AND LOCKOUT ELECTRICAL POWER BEFORE ATTEMPTING ANY SERVICE CAN CAUSE SHOCK, BURNS OR DEATH. WARNING Hazardous voltage Trouble Shooting FAILURE TO DISCONNECT AND LOCKOUT ELECTRICAL POWER BEFORE ATTEMPTING ANY SERVICE CAN CAUSE SHOCK, BURNS OR DEATH. WARNING Hazardous voltage SYMPTOM PROBABLE CAUSE RECOMMENDED ACTION MOTOR NOT RUNNING Motor thermal protector tripped. Allow motor to cool. Insure minimum pump submergence. Clear debris from casing and impeller. NOTE: If circuit breaker “OPENS” Open circuit breaker or blown fuse. Determine cause, call a qualified electrician. repeatedly, DO NOT reset. Call qualified electrician. Pump impeller binding or jammed. Check motor amp draw. If two or more times higher than listed in the “DESCRIPTION AND SPECIFICATIONS” section, impeller is locked, motor bea...

Baixe o seu

Para fazer o download, introduza 2 dígitos :