Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
10. If the equipment should start to abnormally vibrate, STOP the engine/motor and check immediately for the cause. Vibration is generally a warning of trouble. 11. To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease. Never remove or attempt to adjust safety valve. Keep safety valve free from paint and other accumulations. ! WARNING ! CAUTION ! WARNING Never attempt to repair or modify a tank! Welding, drilling or any other modification will weaken the tank resulting in damage from rupture or explosion. Always replace worn or damaged tanks. Drain liquid from tank daily. 13. Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank daily and inspect periodically for unsafe conditions such as rust formation and corrosion. 14. Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system. SPRAYING PRECAUTIONS Do not spray flammable materials in vicinity of open flame or near ignition sources including the compressor unit. 15. Do not smoke when spraying paint, insecticides, or other flammable substances. 16. Use a face mask/ respirator when spraying and spray in a well ventilated area to prevent health and fire hazards. 17. Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from the spraying area as possible to minimize overspray accumulation on the compressor. 18. When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer. ! WARNING ! WARNING ! DANGER Installation LOCATION It is extremely important to use the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 100°F. A minimum clearance of 18 inches between the compressor and a wall is required because objects could obstruct air flow. Do not locate the compressor air inlet near steam, paint spray, sandblast areas or any other source of contamination. This debris will damage the motor. GROUNDING INSTRUCTIONS 1. This product is for use on a nominal 120 volt circuit and has a grounding plug that looks like the plug illustrated in Fig. 1. Make sure the product is connected to an outlet having the same configuration as the plug. This product must be grounded. In the event of an electrical short circuit, grounding reduces risk of electrical shock by providing an escape wire for electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. Plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. Improper use of grounding plug can result in a possible risk of electrical shock! ! DANGER ! CAUTION TEST RESET Figure 1 - Grounding Method Grounding Pin Grounded Outlet No. de Numero No. de Numero Ref. Descripcion de pieza Ctd. Ref. Descripcion de pieza Ctd. Liste de Repuestos Sirvase darnos la siguiente informacion: Puede escribirnos a: -Numero del modelo The Campbell Group / Attn: Parts Department -Numero de Serie (de haberlo) 100 Production Drive -Descripcion y numero del repuesto segun la lista de repuestos Harrison, OH 45030 U.S.A. Para Ordenar Repuestos Sirvase Llamar al Distribuidor Mas Cercano A Su Domicilio 1 Cubierta con mango FP204001AV 1 2 Ensamblaje del mango FP204002AV 1 3 Manometro del tanque FP204012AV 1 4 Regulador FP204013AV 1 5 Multiple FP204003AV 1 6 Valvula de seguridad V-215102AV 1 7 Interruptor FP200343AV 1 8 Llave de drenaje D-1403 1 9 Ensamblaje de la bomba/motor (incluye el cable) FP204004AV 1 10a Tablero del circuito (Modelos FP204000, FP204500) FP204005AV 1 10b Tablero del circuito (Modelos FP20410...
Este manual também é adequado para os modelos :equipamento de bombagem - FP204100 (1.72 mb)
equipamento de bombagem - FP204501 (1.72 mb)
equipamento de bombagem - FP204700 (1.72 mb)