Assessments - 3, GPA: 3.7
(
)
)
|
Facilidade de uso
6. Do not stand on or use the pump or unit as a handhold. 7. Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage. Repair or replace defective items before using. 8. Check all fasteners at frequent intervals for proper tightness. Do not operate unit if damaged Record the Model No., Serial No. and date of purchase located on the base below the pump in the space below. Model No. ____________________ Serial No. ____________________ Date of purchase _________________ Retain these numbers for future reference. © 2002 Campbell Hausfeld For parts, product & service information IN604200AV 1/02visit Portable Handheld Air General Safety (Cont.) ! WARNING Motors, electrical equipment and controls can cause electrical arcs that will ignite a flammable gas or vapor. Never operate or repair in or near a flammable gas or vapor. Never store flammable liquids or gases in the vicinity of the compressor. ! CAUTION Compressor parts may be hot even if the unit is stopped. 9. Keep fingers away from a running compressor; fast moving and hot parts will cause injury and/or burns. 10. If the equipment should start to abnormally vibrate, switch unit OFF (O) and check immediately for the cause. Vibration is generally a warning of trouble. 11. To reduce fire hazard, keep motor free of oil, solvent, or excessive grease. 12. Fast moving air will stir up dust and debris which may be harmful. Release air slowly when draining moisture or depressurizing the compressor system. Any misuse of unit could cause property or equipment damage and/or personal injury. Do not leave the ! WARNING compressor unattended while the unit is running. ! WARNING Never exceed the recommended pressure for any inflatable object. Do not over inflate objects. Over inflation could cause property damage and/or personal injury. Always put the car ! WARNING in park; set the emergency brake; and block the wheels (to stop them from moving) before using the compressor or property damage and/or personal injury could occur. Always use a sep- ! CAUTION arate pressure gauge to check the actual pressure in tires and in low pressure inflatable objects. SPRAYING PRECAUTIONS ! WARNING Do not spray flammable materials in vicinity of open flame or near ignition sources including the compressor unit. 13. Do not smoke when spraying paint, insecticides, or other flammable substances. 14. Use a face mask/ respirator when spraying and spray in a well ventilated area to prevent health and fire hazards. 15. Do not direct paint or other sprayed material at the compressor. Locate compressor as far away from the spraying area as possible to minimize overspray accumulation on the compressor. 16. When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer. Figure 1 Pressure Regulator Pressure Gauge Air Outlet On/Off Switch Handle Location It is extremely important to use the compressor in a clean, well ventilated area where the surrounding air temperature will not be more than 100°F. Do not locate the ! CAUTION compressor air inlet near steam, paint spray, sandblast areas or any other source of contamination. This debris will damage the motor. Electrical Data This product is for ! CAUTION use on a nominal 120 volt circuit. Make sure that product is connected to an outlet having same configuration as plug. WIRING 1. Local electrical wiring codes differ from area to area. Source wiring, plug and protector must be rated for at least the amperage and voltage indicated on motor nameplate, and meet all electrical codes for this minimum. 2. Use a slow blow fuse type T or a circuit breaker. Overheating, short ! CAUTION circuiting and fire damage will result from inadequate wiring, etc. NOTE: This compressor can be operated on a 115 volt, 15 amp circuit under the following conditions: a. Circuit is not heavily loaded. b. Voltage supply is normal. c. Extension cords are of the minimum gauge specified in this instruction manual. d. Circuit is equipped with a 15 amp circuit breaker or a 15 amp slow blow fuse type T. EXTENSION CORDS To avoid loss of NOTICE power and possible overheating, use additional air hose instead of extension cords to reach work area. 1. Use only a 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept plug on product. 2. Make sure extension cord is in good condition, and heavy enough to carry current product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. 2 Model FP2030, FP2031, Electrical Data (Cont.) 3. To avoid loss of power and overheating, it is better to use additional air hose instead of extension cords to reach work area. 4. Table below shows correct size to use depending on cord length and nameplate amper...
Este manual também é adequado para os modelos :equipamento de bombagem - FP2030 (79.02 kb)
equipamento de bombagem - FP2031 (79.02 kb)
equipamento de bombagem - FP2033 (79.02 kb)