Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
Motor Overload Protector (not shown): The motor has an automatic reset thermal overload protector. If the motor overheats for any reason, the overload protector will shut off the motor. The motor must be allowed to cool down before restarting. The compressor will automatically Check Valve restart after the motor cools. HOW TO USE YOUR UNIT How to Stop 1. Set the On/Off switch to "Off". Before Starting Do not operate this unit until you read and understand this Break-in Procedure instruction manual for safety, operation and maintenance instructions. Risk of Unsafe Operation. Serious damage may result if the following break-in instructions are not closely followed. This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced. 1. Make sure the On/Off switch is in the "Off" position. 2. Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit Protection paragraph in the Installation section of this manual.) 3. Open the drain valve (counter-clockwise) fully to permit air to escape and prevent air pressure build up in the air tank during the break-in period. 4. Move the On/Off switch to "On" position. The compressor will start. 5. Run the compressor for 15 minutes. Make sure the drain valve is open and there is minimal air pressure build-up in tank. 6. After 15 minutes, close the drain valve by turning clockwise. The air receiver will fill to "cut-out" pressure and the motor will stop. The compressor is now ready for use. Before Each Start-Up 1. Set the On/Off switch to "Off". 2. Turn the regulator knob counter-clockwise to set the outlet pressure to zero. 3. Attach hose and accessories. Risk of unsafe operation. Firmly grasp air hose in hand when installing or disconnecting to prevent hose whip. Risk of unsafe operation. Do not use damaged or worn 1000003754 12 - ENG accessories. NOTE: The hose or accessory will require a quick connect plug if the air outlet is equipped with a quick connect socket. Risk of Bursting. Too much air pressure causes a hazardous risk of bursting. Check the manufacturer’s maximum pressure rating for air tools and accessories. The regulator outlet pressure must never exceed the maximum pressure rating. Risk of unsafe operation. Compressed air from the unit may contain wa ter condensation and oil mist. Do not spray un fil tered air at an item that could be damaged by moisture. Some air tools and accessories may require filtered air. Read the in struc tions for the air tools and accessories. How to Start 1. Set the On/Off switch to "On" and allow tank pressure to build. Motor will stop when tank pressure reaches "cut-out" pressure. 2. Turn regulator knob clockwise to increase pressure and stop when desired pressure is reached. If any unusual noise or vibration is noticed, stop the compressor immediately and have it checked by a trained service technician. The compressor is ready for use. MAINTENANCE CUSTOMER RESPONSIBILITIES Before each use Daily or after each use Check Safety Valve X Drain Tank X Unit cycles automatically when power is on. When performing maintenance, you may be exposed to voltage sources, compressed air, or moving parts. Personal injuries can occur. Before performing any maintenance or repair, disconnect power source from the compressor and bleed off all air pressure. NOTE: See Operation section for the location of controls. TO CHECK SAFETY VALVE Risk of Bursting. If the safety valve does not work properly, over-pressurization may occur, causing air tank rupture or an explosion. Risk from Flying Objects. Always wear certified safety equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side shields. 1. Before starting compressor, pull the ring on the safety valve to make sure that the safety valve operates freely. If the valve is stuck or does not operate smoothly, it must be replaced with the same type of valve. 13 - ENG 1000003754 NOTE: See Operation section for the location of controls. TO DRAIN TANK Risk of Unsafe Operation. Risk from noise. Air tanks contain high pressure air. Keep face and other body parts away from outlet of drain. Use ANSI Z87.1 eye protection (CAN/CSA Z94.3) when draining as debris can be kicked up into face. Use ear protection [(ANSI S12.6 (S3.19) hearing protection] as air flow noise is loud when draining. 1. Set the On/Off switch to "Off". 2. Turn the regulator knob counter-clockwise to set the outlet pressure to zero. 3. Remove the air tool or accessory. 4. Pull ring on safety valve allowing air to bleed from the tank until tank pressure is approximately 20 PSI. Release safety valve ring. 5. Drain water from air tank by opening drain valve on bottom of tank. Risk of Bursting. Water will condense in the air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture. Risk of Property Damage. Drain water from air tank may con tain oil and rust which can cause stains. 6. After the...