For modEls mAnUFACtUrEd sinCE 02/10 #Cr12612 printEd in ChinA This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installat

Allow it to dry and reinstall. Blow out any accumulated dirt between the cylinder cooling fins. Weekly If the compressor is used on a regular daily basis, perform the following checks each week: 1. Rinse the air filter foam element in water. 2. Check for loose bolts or fittings. Every 300 Hours After every 300 hours or 3 months of regular operation, perform the following maintenance items: 1. Change compressor motor oil. 2. Rinse the air filter foam element in water. 3. Check for air leaks and c

6. Inspect and replace pump piston rings. Compressor 1. Improper oil level. 1. Check oil level and add oil. knocking 2. Air filter clogged. 3. Piston assembly loose. 2. Inspect and clean air filter. 3. Inspect and repair piston and connecting rod. Motor runs hot 1. Cooling fins dirty. 2. Air filter clogged. 1. Clean cylinder fins and motor area. 2. Inspect and clean air filter. Model H3370/H3371Air Compressors -15 PROBLEM CAUSE ACTION Motor runs hot 3. Compressor is exceeding its duty- cycle. 3.

Always wear safety glasses or goggles when operating equipment. Everyday glasses or reading glasses only have impact resistant lenses, they are not safety glasses. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards Institute (ANSI). Operating this equipment has the potential for hearing damage to occur, especially if operated for a long period of time. Use ANSI (American National Standards Institute) approved ear muff or ear plugs when using

Note: Whenever the compressor has not been run for more than a few days, allow it to run with the drain valve open for 5 minutes to fully lubricate the motor. Model G0464/G0465/G0467/G0468/G0470 Air Compressors -11 6. Close the drain valve (Figure 5) to allow the tank to build up pressure. Figure 5.Drain valve. 7. Check the tank pressure gauge (Figure 6) to see that the tank pressure climbs to approximately 115-120 PSI (around 8 BAR), then automatically turns OFF. Note: If the compressor does no

Touching red and black terminal clamps together will cause a short and may cause an explosion or fire. Never touch red and black terminal clamps together! Tire Inflater The air nozzle is tucked inside the storage compartment that is located near the black terminal clamp. If you are filling a tire at night, and you are on the side of the road near oncoming traffic, use the hazard lights to increase your personal safety. To use the tire inflater: 1. Remove the cover to the storage compartment, and

3. Pressure gauge bad. 4. Pressure switch turns the motor OFF too soon. 1. Air leaks in tanks or delivery pipes. 2. Drain valve open. 3. Air filter clogged. 4. Leaking check valve. 5. Pressure relief valve releasing below 120 PSI. 6. Gaskets leaking. 7. Worn rings. 8. Pressure switch turns the motor OFF too soon. 1. Improper oil level. 2. Air filter clogged. 3. Piston assembly loose. 1. Pressure switch adjusted too high. 2. Faulty pressure switch, unit is trying to overpressure the tank. 3. Faul

In no event shall Grizzly’s liability under paid for the product and any legal actions brought of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons special, or consequential damages arising from the use To take advantage of this warranty, contact us by mail or phone and We will then issue you a “Return Authorization Number,” which must be the outside as well as the inside of the carton. We will not accept any item number. Proof of purchase must accompan

(FOR mODELS mANUFACTURED SINCE 9/04) #EW7 339 PRINTED IN CHINA table of contents introduction.....................................................................................2 Foreword...........................................................................................2 Contact Info.......................................................................................2 mACHINE DATA SHEET..................................................................3 section 1: safety...............

Additional information sources are necessary to realize the full potential of this machine. Trade journals, woodworking magazines, and your local library are good places to start. The Model G8297/8298/8299 Air Compressors are specifically designed for air tool operation. DO NOT MODIFY AND/OR USE THIS MACHINE FOR ANY OTHER PURPOSE. Modifications or improper use of this tool will void the warranty. If you are confused about any aspect of this machine, DO NOT use it until you have answered all your