Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
For optimal performance, charge the headset battery for at least six hours before use. When not in use, recharge the headset by returning it to the headset base. 1. Press on both sides of the battery compartment cover and lift the cover up and off. 2. Insert the battery into the battery compartment. 3. Push the battery plug into the connector inside the compartment and ..............................place the wires neatly inside the compartment. 4. Insert the tab on the bottom of the battery cover into the battery compartment. Press down gently on the battery cover until it snaps into place. NOTE: Remove the ear hook from the headset before battery replacement. Getting started Battery charging After installing the battery, charge the headset by placing it in the headset base as shown below. The headset ON/OFF light will be on when the headset is charging. Push ON/OFF light Insert 1. Insert the headset into the headset base. 2. Push the headset downward until the ON/OFF light on the headset turns on. IMPORTANT INFORMATION Use only the supplied rechargeable battery or replacement battery (model BT191545). To obtain a replacement battery, call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Installation preparation If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone line cord and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. For customer service or product information, visit our website at or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Avoid placing the headset base too close to: • Communication devices such as: television sets, VCRs, or other cordless telephones. • Excessive heat sources. • Noise sources such as a window with traffic outside, motors, microwave ovens, refrigerators, or fluorescent lighting. • Excessive dust sources such as a workshop or garage. • Excessive moisture. • Extremely low temperature. • Mechanical vibration or shock such as on top of the washing machine or work bench. Headset base installation IMPORTANT: If you purchased model TL7611, see the TL7000 handset lifter manual for installation instructions. Optional accessories It is recommended that you install a handset lifter (model TL7000) and/or a dial pad (model TL7601) with your headset. The following optional accessories are compatible with your headset and base: The TL7000 is a handset lifter with ring detector. The TL7601 is a dial pad that allows you to dial numbers and place calls when away from your telephone. The dial pad will also allow you to use the headset as a stand-alone product without a connection to a telephone. The TL7600 is an expansion headset (up to two headsets can be used with the same headset base). Visit our website for more information about these products or to download user manuals. TL7000 TL7601 TL7600 Headset base installation Installation options IMPORTANT: If you purchased model TL7611, or if you purchased a model TL7000 handset lifter (purchased separately), follow the installation instructions in the TL7000 handset lifter manual and then proceed on page 10 of this quick start guide. If you purchased model TL7610 (without handset lifter), you have three installation options: Option 1: Use the headset with a single standard telephone line with a corded or cordless telephone. Option 2: Use the headset with a single standard telephone line as a stand-alone product. Option 3: Use the headset with a multiple line corded telephone (such as the AT&T 1080, 1070, 1040) or a digital business system (such as a proprietary PBX telephone system). Cord labels The cords provided with your headset have colored labels attached to help you plug them into the headset base. The back of the headset base has colored dots above the jacks, and the jack names on the rear bottom plastic piece of the headset base that correspond to the colored labels on the cords. If you are using installation option 3: You may attach the provided light blue colored label to the end of your telephone curly handset cord that you will plug into the headset base. Digital subscriber line (DSL) If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone base and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. Headset base installation Before installing the headset base: Remove the rear bottom piece of the headset base by pushing it away from the base (as shown in Figure 1). Install the headset base as shown on the following pages. After completing installation option 1 or 2: Slide the rear bottom piece tow...