Assessments - 1, GPA: 5
(
)
)
|
Facilidade de uso
6 Connect the DC power output connector of the 12 Volt/ 200mA AC/DC adapter to the DC POWER INPUT JACK at the back of the transmitter. 7 Connect the 12 Volt/200mA AC/DC adapter to the mains socket. Always remove the adapter from the mains socket if the transmitter will not be used for a period of time. Charging the headphone 8 Place the headphone onto the energizing docking station, and make sure the charging pins of the transmitter and the charging contact of the headphone are well aligned. The CHARGING INDICATOR light will be on automatically indicating charging is taking place. At the same time, the headphone will power off automatically (i.e. POWER ON/OFF INDICATOR lights off). When charging is finished (which takes approximately 16 hours), the green CHARGING INDICATOR light will also be off automatically. IMPORTANT! • The energizing docking station does not transmit audio signal when charging is activated. WARNING! • Before using the FM headphone for the first time, please ensure that the batteries are fully charged for at least 16 hours. This will guarantee a longer operating lifetime of batteries. • This product complies with the latest safety regulations. Please only charge the batteries with the docking station provided (SHC8545) or with fully compatible charger. Audio Connection 9 Connect one end of the audio cable (3.5 mm stereo plug) to the transmitter’s 3.5 mm STEREO INPUT JACK. 10 Connect the other end of the 3.5 mm stereo cable to either: a) The headphone output of an audio source, such as TV, HiFi or PC. Adjust the volume level of the audio source to a fixed reasonably high level; for example 25% of the maximum level. • In case your audio source has a 6.3mm headphone output, use the supplied 3.5mm to 6.3mm stereo adapter plug. IMPORTANT! • In case of certain TVs, the headphone jack output level can only be adjusted after accessing the TV on-screen menu. b) The line output of an audio source, such as REC OUT or LINE OUT (with the Y-cable supplied). • Check if the red RCA plug (right channel) is connected to the right channel (red) of the audio source. • Check if the white RCA plug (left channel) is connected to the left channel (white) of the audio source. • In case the audio source has an adjustable RCA output level, adjust the output level to the highest acceptable undistorted level. 11 Switch on your audio source and carefully increase the volume of the audio source. The POWER ON/OFF INDICATOR of the transmitter lights up when signals are received. 12 Switch on the POWER ON/OFF button of the headphone. The POWER ON/OFF INDICATOR will be switched on automatically. 13 Press and hold the AUTO-TUNING BUTTON on the headphone for about 1 second to tune to the correct transmission channel. The headphone will automatically tune to the transmitter. 14 In case interference from neighbouring transmitters has occured, adjust the transmission channel of the transmitter, then repeat step 13 to tune the headphone to the transmitter. 15 Adjust the volume of the headphone to the desired listening level. IMPORTANT! • Avoid adjusting the listening volume level at the audio source as this may compromise the audio quality on too low input levels. Problem solving If a fault occurs, first check the points listed below. If you are unable to remedy a problem by following these hints, contact the helpline (see ‘Need help?’) or consult your dealer. Never tr y to open the set yourself as this will void the guarantee. First, check all cables to ensure that they are connected correctly. Problem Possible Cause Solution Headphone fails No battery installed Follow step 1 to 4 of to charge ‘Installing/replacing the batteries’ Wrong battery orientation Reposition the batteries according to the engraved polarity symbol. No power supply Make sure the docking station is connected to the local mains power supply through an adapter and follow steps 5 to 7. Charging pin of the docking station Lock the headphone in place, and not in contact with the metal make sure the CHARGE plate of the headphone INDICATOR light is on. Wrong headphone orientation Reposition the headphone with when placed onto the charging correct orientation. dock No sound/ Headphone power off Push the POWER ON/OFF distorted sound BUTTON. The POWER ON/OFF INDIC ATOR light turns on automatically indicating the headphone is on. No battery installed Follow step 1 to 4 of ‘Installing/replacing the batteries’ Wrong battery orientation Reposition the batteries according to the engraved polarity symbol. No power supply to transmitter Make sure the docking station is connected to the local mains power supply through an adapter and follow step 5 to 7. Battery power running low Follow steps 5 to 7 to recharge the system. Audio source not connected Make sure the audio output of your audio source is connected to the 3.5 mm STEREO INPUT JACK of your transmitter. Follow step 9 to 12. Audio source is off Turn on your audio source. Volume level set too low Adjust the volume lev...