A Click [start] - [Control Panel] - [Performance and Maintenance] - [Administrative Tools], and double-click [Computer Management]. B Click [Disk Management] from [Storage]. C Right-click the hard disk partition or the CD/DVD drive name, and click [Change Drive Letter and Paths...]. D Click [Change...]. E Click [Assign the following drive letter] and the new drive letter, and then click [OK]. At the confirmation message, click [Yes]. Useful Information Error Code/Message Follow the instructions below when an error message or code appears. If the problem persists or if the error code/message is not shown here, contact Panasonic Technical Support (• page 29). Error Code/Message Solution 0211 Keyboard error • Disconnect external keyboard or mouse. 0251 System CMOS checksum bad Default configuration used An error has occurred in the memory of Setup Utility settings. This occurs when the memory content is changed by an unexpected program operation, etc. • Start the Setup Utility and return the settings to the default values, and then change the settings as necessary. • If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support (• page 29). 0271 Check date and time settings The date and time settings are not correct. • Start the Setup Utility and set the correct date and time. • If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support (• page 29). 0280 Previous boot incomplete -Default configuration used Startup has failed repeatedly, so the Setup Utility settings have been returned to the default values to startup the computer. • Start the Setup Utility and return the settings to the default values, and then change the settings as necessary. Press to Setup • Write down the error details and press F2 to start the Setup Utility. Change the settings if necessary. Operating System not found The operating system is not installed in the floppy disk or the hard disk that you are going to boot from. • If using a floppy disk, change the disk to the one you can use for boot. • If using the hard disk, check if the hard disk is recognized in [Information] menu of the Setup Utility. If the hard disk is recognized, perform the reinstallation (• page 17). If not, contact Panasonic Technical Support (• page 29). • If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in [Advanced] menu of the Setup Utility. RAM Module Failed When the RAM module is not inserted correctly or the RAM module is not conforming to the computer’s specifications, so a beep will sound and the “RAM Module Failed” message will be displayed when you turn the power on. • Press the power button for four seconds or longer to turn off the computer, confirm that the RAM module conforms to the specifications, and reinsert it. • To start the Setup Utility A Restart the computer. B Press F2 several times while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. Troubleshooting Troubleshooting (Basic) Troubleshooting Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support (• page 29). You can also check the computer’s status in the PC Information Viewer (• Reference Manual “Troubleshooting (Advanced)”). • Starting Up Cannot start up. The power indicator or battery indicator is not lit. • Connect the AC adaptor. • Insert a fully charged battery. • Remove the battery pack and the AC adaptor, then connect them again. • Remove the USB device, or set [USB Port] or [Legacy USB Support] to [Disable] in [Advanced] menu of the Setup Utility. The computer may not start up when certain USB devices are connected. The power is turned on but • The computer is warming up before start up. Wait for the computer to start up (takes “Warming up the system (up up to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed to 30 minutes)” appears. to warm up and does not start. In this case, turn off the computer, leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the power once more. Cannot turn on the computer. • Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, The computer does not then turn on the power once more. resume from standby mode. (The power indicator blinks quickly in green.) You have forgotten the password. • Supervisor Password or User Password: Contact Panasonic Technical Support (• page 29). • Administrator password: • If you have a password reset disk, you can reset the administrator password. Set the disk and enter any wrong password, then follow the on-screen instructions and set a new password. • If you do not have a password reset disk, rei...
)
