Assessments - 2, GPA: 4 ( )

Fabricante : Toshiba Arquivo Tamanho: 3.58 mb Arquivo Nome : Língua de Ensino:

When the feature is active, you must enter the password during the power-on process. After typing your password, press the Enter key. If the password is correct, the power-on process continues. If the password is incorrect, you will be prompted to try again. If you forget your power-on password and therefore cannot turn on your computer, take your computer to a Toshiba authorized service center for help. After the third incorrect password submission, the system automatically shuts down. Using the TouchPadTM The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you’d like to move the cursor: . To move the cursor to the top of the page, push your finger forward on the TouchPad. . To move the cursor to the bottom of the page, drag your finger toward yourself. . To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. 64 64 64 Using the computer for the first time . To move it to the left side, slide your finger from right to left. Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can either click it into place by double-tapping the TouchPad or clicking the control buttons. For more on the TouchPad, see “Lesson 2: Using the TouchPad and control buttons together” on page 139. Control buttons When a step instructs you to click or choose an item, move the cursor to the item, then press and release the primary (left-hand) button. To double-click, press the primary button twice in rapid succession. The primary button usually corresponds to the left mouse button. The function of the secondary (right-hand) button depends on the program you are using. It usually corresponds to the right mouse button. Check your program’s documentation to find whether it uses the right mouse button. Disabling or enabling the TouchPad The TouchPad is enabled by default. To change the enable/ disable TouchPad setting by using the Fn + F9 keys, see “Disabling or enabling the TouchPad” on page 242. You may also change the enable/disable setting as follows: 1 Click Start, Control Panel. The Control Panel window appears. 2 Click Printers and Other Hardware. Getting Started Getting Started Installing additional memory (optional) 3 Click Mouse Properties. The Mouse Properties window appears. 4 Click the TouchPAD ON/OFF tab. The TouchPAD ON/OFF tab view window appears. 5 Select Disable or Enable, whichever is appropriate. 6 Click Apply. 7 Click OK. The Mouse Properties window closes. 8 Close the Printers and Other Hardware window. 9 Close the Control Panel window. Installing additional memory (optional) Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost. A memory module must be installed in slot A. Do not try to operate the computer with a memory module in slot B only. Your computer is equipped with two memory slots which can provide for various memory configurations. When additional memory is added, or original memory replaced, it is recommended that you use only compatible memory. In the event original memory is replaced with invalid memory, the system will beep and will not start up beyond the BIOS memory check. A message will display. If this occurs, contact Toshiba’s support center. See “Toshiba voice contact” on page 233. 66 66 66 Installing additional memory (optional) HINT: To purchase additional memory modules, visit the Toshiba Web site at toshiba.com. Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data. There are two memory slots. Your system may have both slots occupied. If you use the computer for a long time, the memory modules will become hot. If this happens, let the modules cool to room temperature before you replace them. Do not try to install a memory module under the following conditions. You can damage the computer and the module. 1. The computer is turned on. 2. The computer was shut down using Standby mode. 3. Power to the DVD-ROM or multi-function drive has been turned on. Do not install or remove a memory module while the DVDROM or multi-function drive power is on. Getting Started Getting Started Installing additional memory (optional) You will need a standard Phillips No.1 screwdriver and a small flat-head screwdriver to install a memory module. To avoid damaging the computer’s screws, use a standard Phillips screwdriver that is in good condition. 1 If the computer is on, turn it off. See “Turn Off or Shut down command” on page 1...

Baixe o seu

Para fazer o download, introduza 2 dígitos :