Assessments - 3, GPA: 3.3 ( )

Fabricante : Toshiba Arquivo Tamanho: 2.91 mb Arquivo Nome : Língua de Ensino:

Getting Started 59 Adding memory (optional) Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory module. Do not remove the memory module while the computer is in Standby or Hibernation mode. The computer could hang up the next time you turn it on and data in memory will be lost. In either of the above cases, the Standby configuration will not be saved. The following message appears when you turn on the power: Warning: Resume Failure Press Any Key to Continue If the computer hangs up when you turn it on, perform the following: Press the power button and hold it down for at least ten seconds, then turn the power on again. 2 Pull the latches away from the memory module. The memory module pops up slightly. NOTE If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module. 1 Gently lift the memory module to a 30-degree angle and slide it out of the slot. 60 60 Getting Started Adding memory (optional) Front of Memory slots computer (Sample Illustration) Removing the memory module 2 Replace the memory module slot cover and secure it using the screw. 3 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 119. 4 Turn the computer right side up. 5 Reconnect the cables. 6 Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Getting Started 61 Using the TouchPad™ Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change. To do this: 1 Click Start, Control Panel, Performance and Maintenance, and then System. 2 The General tab view automatically appears and shows total memory. If the computer does not recognize the memory configuration, turn off the computer, remove the memory slot cover, and check that the module is inserted completely into the socket and lined up squarely with the socket latches. Using the TouchPad™ The TouchPad™, the small, smooth, square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you would like to move the cursor: . To move the cursor to the top of the page, push your finger forward on the TouchPad. . To move the cursor to the bottom of the page, drag your finger toward yourself. . To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. . To move it to the left side, slide your finger from right to left. NOTE Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. 62 62 Getting Started Using the TouchPad™ Once you have positioned your cursor, you can click it into place by either double-tapping the TouchPad or clicking the control buttons. Scrolling with the TouchPad™ There are two active regions on the TouchPad™ that allow you to scroll as you would with any wheel device on a mouse or trackball. To scroll vertically, run your finger up or down along the right edge of the TouchPad. To scroll horizontally, run your finger along the bottom edge of the TouchPad. This feature can be disabled or changed in the Mouse Properties dialog box. Control buttons When a step instructs you to click or choose an item, move the cursor to the item, then press and release the primary (left-hand) button. To double-click, press the primary button twice in rapid succession. The primary button usually corresponds to the left mouse button. The function of the secondary (right-hand) button depends on the program you are using. It usually corresponds to the right mouse button (“right-clicking”). Check your program’s documentation to determine whether it uses the right mouse button. Disabling or enabling the TouchPad™ The TouchPad™ is enabled by default. To change the enable/ disable TouchPad setting: 1 Click Start, and then Control Panel. The Control Panel window appears. 2 Click Printers and Other Hardware. 3 Click the Mouse icon. The Mouse Properties window appears. Getting Started 63 Using the TouchPad™ Click the Device Settings tab. The Device Settings tab view window appears. (Sample Image) Device Settings tab screen 5 Select Disable or Enable, whichever is appropriate. 6 Click Apply. 7 Click OK. The Mouse Properties window closes. 8 Close the Printers and Other Hardware window. 9 Close the Control Panel window. You can also use a hot key to disable or enable the TouchPad. See “Disabling or enabling the TouchPad” on page 240. 64 64 Getting Started Using external display devices Using external display devices Your computer comes with a built-in LCD display, but you can also connect an external display device to the available video port: . An external monitor ...

Baixe o seu

Para fazer o download, introduza 2 dígitos :