Assessments - 1, GPA: 5
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
14.1-Inch Display Panel 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display bezel. 4. Remove the eight M2 x 5-mm screws from each side of the display- panel adapter rails. 5. Lift the display panel, and rotate the display panel out of the display cover. 6. Remove the four M2 x 3-mm screws from each side of the display panel to remove the adapter rails. When reinstalling the adapter rails to the replacement display panel, orient the rails so that the "This side up" markings are facing you, and then reattach the rails with the M2 x 3-mm four screws. (The "This side down" markings on the rails should be visible from the backside of the display panel.) 7. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector. 8. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. 1 14.1-inch display panel 2 adapter rails (2) 3 M2 x 3-mm screws (4) 4 "This side up" markings 15-Inch Display Panel 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display bezel. 4. Remove the eight M2 x 5-mm screws from each side of the display panel. 5. Lift the display panel, and rotate the display panel out of the display cover. 6. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector. 7. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. 1 pull-tab on bottom flex-cable connector 2 top flex-cable connector 3 display connector 4 inverter connector CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. 1 pull-tab on bottom flex-cable connector 2 top flex-cable connector 3 display connector Display Latch 1. Remove the keyboard. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the M2 x 5-mm screw that secures the display bracket to the top cover. 5. Lift the display bracket out of the top cover, and then remove the display latch. Back to Contents Page 4 inverter connector NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTE: Ensure that the display bracket is upright when you replace the display latch. 1 top cover 2 M2 x 5-mm screw (1) 3 display bracket 4 display latch Back to Contents Page Docking Doors Dell™ Inspiron™ 510m Service Manual Removing the Docking Doors 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Gently bend the docking doors and lift them away from the computer base. Installing the Docking Doors Slide the side of the docking doors with the spring over the longer posts. CAUTION: Before working inside your computer, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 docking doors Back to Contents Page 1 docking doors with spring 2 longer post Back to Contents Page Fan Dell™ Inspiron™ 510m Service Manual 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the palm rest. 4. Remove the microprocessor thermal-cooling assembly. 5. Pull straight up on the fan cable connector to disconnect it from the system board connector. 6. Remove the two M2.5 x 8-mm screws from the fan, and pull the fan away from the system board. Back to Contents Page CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 M2.5 x 8-mm screws (2) 2 fan 3 fan cable connector 4 system board connector Back to Contents Page Hard Drive Dell™ Inspiron™ 510m Service Manual 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Turn the computer over. Use a standard #1 Phillips screwdriver to remove the two M2.5 x 5- mm screws. 3. Slide the hard drive out of the computer. 4. Remove the new drive from its packaging. Save the original packaging to use when storing or shipping the hard drive. 5. Press the hard drive cover down until it is...