Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 4. Turn the computer over, and remove the two M3 x 5-mm screws from the bottom of the computer. 5. Turn the computer over, and open the display 180 degrees. 6. Disconnect the antenna connector. 7. Disconnect the signal cable from the system board. 8. Remove the tape that secures the inverter connector, and then disconnect the inverter cable from the system board. 1 M2 x 6-mm screws (2) 1 M3 x 5-mm screws (2) NOTICE: Do not pull on the signal cable and inverter cable. Pull from the signal connector and inverter connector to disconnect the cables. 9. Move the display assembly to an upright position and pull it up out of the bottom case. Back to Contents Page 1 signal cable 2 inverter cable 3 inverter connector 4 signal connector Back to Contents Page Cooling Fan Dell™ X200 Service Manual Removing the Cooling Fan 1. Remove the battery. 2. Remove the keyboard. 3. Remove the palm rest. 4. Remove the hinge covers. 5. Remove the display assembly. 6. Remove the keyboard tray. 7. Remove the four M2 x 3-mm screws that secure the cooling fan to the system board. 8. Remove the tape that secures the cooling fan cable to the fan. 9. Disconnect the cooling fan cable from the system board connector. 10. Lift the cooling fan up and out of the bottom case. Back to Contents Page NOTICE: Disconnect the computer and any attached devices from electrical outlets. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1 cooling fan connector 2 cooling fan cable 3 cooling fan 4 M2 x 3-mm screws (4) 5 system board connector NOTICE: Do not pull on the cooling fan cable. Pull from the cooling fan connector to disconnect the cable. Back to Contents Page Hard Drive Dell™ X200 Service Manual Removing the Hard Drive 1. Remove the battery. 2. Remove the keyboard. 3. Remove the palm rest. 4. Loosen the three M2 x 5.5-mm screws that secure the hard drive to the bottom case. Rubber grommets secure each screw to the hard drive so that you do not need to completely remove the screws. 5. Disconnect the hard drive connector from the system board. 6. Lift the hard drive up and out of the bottom case. Back to Contents Page NOTICE: Disconnect the computer and any attached devices from electrical outlets. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. NOTE: Each hard drive screw has an arrow beside it. 1 hard drive 2 M2 x 5.5-mm screws (3) 3 hard drive connector Back to Contents Page Keyboard Dell™ X200 Service Manual Removing the Keyboard 1. Remove the battery. 2. Remove the six M2 x 4-mm screws labeled with an arrow (one of the six screws is labeled "K" with an arrow) from the bottom of the computer. 3. Turn the computer over, and insert a .-inch flat-blade screwdriver into the slot to the right of the keyboard locator tab. NOTICE: Disconnect the computer and any attached devices from electrical outlets. NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure. 1 M2 x 4-mm screws (6) NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time- consuming to replace. Be careful when removing and handling the keyboard. 4. Pry up the keyboard locator tab, and the keyboard pops up. 5. Pull the keyboard a small distance toward the front of the computer to release the four securing tabs located across the back edge of the keyboard. 6. Rotate the keyboard toward the front of the computer and place it face-down on the palm rest. 7. Open the ZIF connector on the system board by pulling the ZIF connector tabs toward the back of the computer. 8. Remove the keyboard flex cable from the ZIF connector. 9. Lift the keyboard up and out of the computer. Replacing the Keyboard 1. Place the keyboard face-down on the palm rest, with the keyboard flex cable pointing toward the back of the computer. 1 keyboard locator tab 2 keyboard securing tabs (4) NOTICE: Do not pull on the keyboard flex cable. 1 keyboard flex cable 2 ZIF connector 3 ZIF connector tabs (2) 2. Ensure that the ZIF connector is open by pulling the ZIF connector tabs toward the back of the computer. 3. Press the keyboard flex cable into the ZIF connector. 4. Close the ZIF connector by pushing the ZIF connector tabs toward the front of the computer. To aid with proper flex cable connection, a blue locator line has been added near the end of the flex cable. Pres...