Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
If either the processor or heat sink is replaced, use the thermal pad provided in the kit to ensure that thermal conductivity is achieved. NOTE: This procedure assumes that you have already removed the processor heat sink and are ready to replace it. 3. Follow the instructions from step 4 to step 24 in Replacing the System Board. Back to Contents Page CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. Back to Contents Page Display Dell™ Inspiron™ 1464 Service Manual Display Assembly Display Bezel Display Panel Display Cable Display Panel Brackets Display Hinges Display Assembly Removing the Display Assembly 1. Follow the procedures in Before You Begin. 2. Remove the battery (see Removing the Battery). 3. Remove the optical drive (see Removing the Optical Drive). 4. Remove the module cover (see Removing the Module Cover). 5. Disconnect the Mini-Card antenna cables (see step 4 in Removing the Mini-Card). 6. Note the routing of the Mini-Card antenna cables and remove them from the routing guides on the bottom of the computer. 7. Remove the two screws on the bottom of the computer that secure the display assembly to the computer base. 8. Remove the power button panel (see Removing the Power Button Panel). WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface. CAUTION: To help prevent damage to the system board, remove the main battery (see Removing the Battery) before working inside the computer. 1 screws (2) 2 Mini-Card antenna cable routing 9. Remove the keyboard (see Removing the Keyboard). 10. Pull the Mini-Card antenna cables up through the slot in the computer base. 11. Note the routing of the Mini-Card antenna cables and remove them from the routing guides on the palm rest. 12. Disconnect the display cable from the connector on the system board and remove the display cable grounding screw. 13. Remove the three screws that secure the display assembly to the computer base. 14. Lift the display assembly off the alignment posts on the computer base. Replacing the Display Assembly 1. Follow the procedures in Before You Begin. 2. Use the alignment posts to place the display assembly on the computer base. 3. Replace the three screws that secure the display assembly to the computer base. 4. Connect the display cable to the connector on the system board and replace the display cable grounding screw. 5. Route the Mini-Card antenna cables through the routing guides on the palm rest. 6. Thread the Mini-Card antenna cables through the slot in the computer base. 7. Turn the computer over and replace the two screws that secure the display assembly to the computer base. 1 Mini-Card antenna cables 2 display cable grounding screw 3 display cable 1 screws (3) 2 display assembly 8. Route and connect the Mini-Card antenna cables (see step 5 in Replacing the Mini-Card). 9. Replace the module cover (see Replacing the Module Cover). 10. Replace the keyboard (see Replacing the Keyboard). 11. Replace the power button panel (see Replacing the Power Button Panel). 12. Replace the optical drive (see Replacing the Optical Drive). 13. Replace the battery (see Replacing the Battery). Display Bezel Removing the Display Bezel 1. Follow the procedures in Before You Begin. 2. Remove the display assembly (see Removing the Display Assembly). 3. Carefully pull up around the inside edges of the display bezel to remove it from the display assembly. Replacing the Display Bezel 1. Follow the procedures in Before You Begin. 2. Ensure the display cable and Mini-Card antenna cables run through the notch on the left hinge to keep the cables clear of the display bezel. 3. Place the display bezel over the hinges first. 4. Gently press down around the display bezel to snap it into place. 5. Replace the display assembly (see Replacing the Display Assembly). 6. Replace the battery (see Replacing the Battery). CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. CAUTION: The display bezel is extremely fragile. Be careful when removing it to prevent damaging the bezel. 1 display assembly 2 display bezel CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. Display Panel Removing the Display Panel 1. Foll...