Assessments - 0, GPA: 0
(
)
)
|
por este dispositivo também tem outras instruções :
Facilidade de uso
NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket. 1. Align the pin-1 corner of the microprocessor module with the pin-1 corner of the ZIF socket, and insert the microprocessor module. NOTE: The pin-1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket. NOTICE: You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket. When the microprocessor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the others, the module is not seated correctly. 2. Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board. 3. Replace the other computer parts you removed earlier in this procedure. 4. Update the BIOS using a flash BIOS update program floppy disk or CD. For instructions on how to flash the BIOS, see "Flashing the BIOS." Back to Contents Page Back to Contents Page Display Assembly and Display Latch Dell™ Latitude™ D505 Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: You must remove the display assembly before you remove the palm rest. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Open the display assembly approximately 180 degrees, and support the display assembly so that it does not open past this position. 4. Pull up on the pull-tab that is attached to the display cable connector to remove the connector from the system board. 5. Release the display cable from the three display-cable routing clips. 6. Release the two antenna cables from the two antenna-securing clips. 7. Disconnect one antenna cable from the display by holding the two gold antenna connectors and gently pulling them apart. Then disconnect the other antenna cable. (The gold antenna connectors on each cable are keyed to ensure that they are correctly reconnected.) 1 M2.5 x 5-mm screws (4) 63PDH 5 pull-tab 2 display cable connector 6 system board connector 3 display see Mini RSL 7 antenna securing clips (2) 4 computer base 8 antenna connectors (4) 8. Remove the four M2.5 x 5-mm screws. 9. Rotate the display assembly to a 90-degree angle, and lift the display assembly up and out of the computer base. 14.1-Inch Display 1 M2 x 5-mm screws (6) 1428U 5 top cover H1375 2 display bumpers (6) K1681 6 M2 x 5-mm screws (8) 1428U 3 display bezel X1261 7 adapter rails (2) F3774 4 display panel F1788 8 M2 x 3-mm screws (4) 4270E 15-Inch Display 1 M2 x 5-mm screws (6) 1428U 4 display panel D1724 2 display bumpers (6) K1681 5 top cover H1375 3 display bezel H1370 6 M2 x 5-mm screws (8) 1428U Display Bezel CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display assembly. 4. Use a plastic scribe to pry the six display bumpers out of the screw holes located on the front of the bezel. 5. Remove the six M2 x 5-mm screws located on the front of the bezel. NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel. 6. Starting at the bottom of the display panel (by the DELL™ logo), use your fingers to separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover. Display Panel 14.1-Inch Display Panel CAUTION: Before performing the following procedures, read the safety instructions in your Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display bezel. 4. Remove the eight M2 x 5-mm screws from each side of the display-panel adapter rails. 5. Lift the display panel, and rotate the display panel out of the display cover. 6. Remove the four M2 x 3-mm screws from each side of the display panel to remove the adapter rails. When reinstalling the adapter rails to the replacement display panel, orient the rails so that the "This side up" markings are facing you, and then reattach the rails with the four M2 x 3-mm screws. (The "This side down" markings on t...