Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Improper handling of static-sensitive parts can cause damage to the part. When you unpack an option or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: • Limit your movement. Movement can cause static electricity to build up around you. • Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry. • Prevent others from touching components. • When you install a static-sensitive option or CRU, touch the static-protective package containing the part to a metal expansion-slot cover or other unpainted metal surface on the computer for at least two seconds. This reduces static electricity in the package and your body. • When possible, remove the static-sensitive part from the static-protective packaging and install the part without setting it down. When this is not possible, place the static-protective packaging on a smooth, level surface and place the part on it. • Do not place the part on the computer cover or other metal surface. Replacing the battery Before you start, print these instructions. This system might not support batteries that are not genuine Lenovo-made or authorized. These systems will continue to boot, but might not charge unauthorized batteries. Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use. To replace the battery with a new one, read the following prerequisites. © Copyright Lenovo 2011 Prerequisites for the procedure DANGER If the rechargeable battery pack is incorrectly replaced, there is danger of an explosion. The battery pack contains a small amount of harmful substances. To avoid possible injury: • Replace only with a battery of the type recommended by Lenovo. • Keep the battery pack away from fire. • Do not expose it to excessive heat. • Do not expose it to water or rain. • Do not short-circuit it. • Do not drop, crush, puncture, or subject to strong forces. Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to “vent” from the battery pack or coin cell. Replacing the battery To replace the battery, follow the procedure below. 1. Turn off the computer, or enter hibernation mode. Then disconnect the ac power adapter and all cables from the computer. 2. Close the computer display, and turn the computer over. 3. Slide and hold the battery latches to the unlock position 1 , and remove the battery 2. 72 User Guide 4. Insert a fully charged battery until it clicks into place 1 , and then slide the battery latch to the locked position 2. 5. Turn the computer over again. Reconnect the ac power adapter and all cables. Replacing the solid state drive or hard disk drive You can replace the solid state drive or hard disk drive with a new one that can be purchased from your Lenovo reseller or a marketing representative. To replace the solid state drive or hard disk drive, read the following prerequisites. Note: Replace the solid state drive or hard disk drive only if you upgrade it or have it repaired. The connectors and slot of the solid state drive or hard disk drive were not designed for frequent changes, or drive swapping. Prerequisites for the procedure When replacing the drive, be sure to follow the precautions. Attention: When handling a solid state drive or hard disk drive • Do not drop the drive or subject it to physical shocks. Put the drive on a material, such as soft cloth, that absorbs any physical shocks. • Do not apply pressure to the cover of the drive. • Do not touch the connector. The drive is very sensitive. Incorrect handling can cause damage and permanent loss of data. Before removing the solid state drive or hard disk drive, make a backup copy of all the information on it, and then turn the computer off. Never remove the drive while the computer is operating, in sleep (standby) mode, or in hibernation mode. Replacement instructions To replace the solid state drive or hard disk drive, do as follows: 1. Turn off the computer; then disconnect the ac power adapter and all cables from the computer. 2. Close the computer display, and turn the computer over. Chapter 6. Replacing devices 73 3. Remove the battery. For information about how to remove the battery, refer to “Replacing the battery” on page 71. 4. Loosen the screws 1 that secure the solid state drive or hard disk drive door 2 , and then remove the solid state drive or hard disk drive door. 5. Remove the screws 1 , and then slide the solid state drive or hard disk drive in the direction shown by the arrow 2. 74 User Guide 6. Remove the solid state drive or hard disk drive by lifting its left side. 7. Insert the new solid state drive or hard disk drive as shown in the following p...
Este manual também é adequado para os modelos :Notebooks - ThinkPad X130e (0627) (2.92 mb)
Notebooks - ThinkPad X130e (0629) (2.92 mb)
Notebooks - ThinkPad X130e (2338) (2.92 mb)
Notebooks - ThinkPad X130e (2339) (2.92 mb)