Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
82750 Third Edition • Third Printing Operator's Manual SAFETY RULES Do not alter or disable the limit switches. Do not drive over 0.5 mph / 0.8 km/h with the platform raised. Do not depend on the tilt alarm as a level indicator. The tilt alarm sounds on the chassis and in the platform when the machine is on a severe slope. If the tilt alarm sounds: Lower the platform. Move the machine to a firm, level surface. If the tilt alarm sounds when the platform is raised, use extreme caution to lower the platform. Do not raise the platform unless the machine is on a firm, level surface. Do not use the platform controls to free a platform that is caught, snagged or otherwise prevented from normal motion by an adjacent structure. All personnel must be removed from the platform before attempting to free the platform using the ground controls. Do not alter or disable machine components that in any way affect safety and stability. Do not replace items critical to machine stability with items of different weight or specification. Do not operate the machine in strong or gusty winds. Do not increase the surface area of the platform or the load. Increasing the area exposed to the wind will decrease machine stability. Do not drive the machine on or near uneven terrain, unstable surfaces or other hazardous conditions with the platform raised. Use extreme care and slow speeds while driving the machine in the stowed position across uneven terrain, debris, unstable or slippery surfaces and near holes and drop-offs. Do not push off or pull toward any object outside of the platform. GS-2668 DC ANSI & CSA - 4 person 200 lbs / 890 N Australia - Indoor use only - 4 person 90 lbs / 400 N Australia - Outdoor use - 4 person 90 lbs / 400 N GS-3268 DC ANSI & CSA - 4 person 200 lbs / 890 N Australia - Indoor use only - 4 person 90 lbs / 400 N Australia - Outdoor use - 2 person 90 lbs / 400 N Part No. 82750 Genie GS-2668 DC and Genie GS-3268 DC Operator's Manual Third Edition • Third Printing SAFETY RULES Do not modify or alter an aerial work platform without written permission from the manufacturer. Mounting attachments for holding tools or other materials onto the platform, toeboards or guard rail system can increase the weight in the platform and the surface area of the platform or the load. Do not place or attach fixed or overhanging loads to any part of this machine. Do not place ladders or scaffolds in the platform or against any part of this machine. Do not transport tools and materials unless they are evenly distributed and can be safely handled by person(s) in the platform. Do not use the machine on a moving or mobile surface or vehicle. Be sure all tires are in good condition, castle nuts are properly tightened and lock plates are properly installed. Do not use the machine as a crane. Do not push the machine or other objects with the platform. Do not contact adjacent structures with the platform. Do not tie the platform to adjacent structures. Do not place loads outside the platform perimeter. Do not use batteries that weigh less than the original equipment. Batteries are used as counterweight and are critical to machine stability. Each battery must weigh 65 pounds / 29.5 kg. Fall Hazards The guard rail system provides fall protection. If occupants of the platform are required to wear personal fall protection equipment (PFPE) due to job site or employer rules, PFPE equipment and its use shall be in accordance with the PFPE manufacturer’s instructions and applicable governmental requirements. Do not sit, stand or climb on the platform guard rails. Maintain a firm footing on the platform floor at all times. Do not climb down from the platform when raised. Keep the platform floor clear of debris. Close the entry gate before operating. Do not operate the machine unless the guard rails are properly installed and the entry is secured for operation. Genie GS-2668 DC and Genie GS-3268 DC Part No. 82750 Third Edition • Third Printing Operator's Manual Collision Hazards Be aware of limited sight distance and blind spots when driving or operating. Be aware of the extended platform position when moving the machine. The machine must be on a level surface or secured before releasing the brakes. Operators must comply with employer, job site and governmental rules regarding the use of personal protective equipment. Check the work area for overhead obstructions or other possible hazards. Be aware of crushing hazards when grasping the platform guard rail. Observe and use the color-coded direction arrows on the platform controls and platform decal plate for drive and steer functions. Do not operate a machine in the path of any crane or moving overhead machinery unless the controls of the crane have been locked out and/or precautions have been taken to prevent any potential collision. No stunt driving or horseplay while operating a machine. SAFETY RULES Do not lower the platform unless the area below is clear of personnel and obstructions. Limit trave...
Este manual também é adequado para os modelos :Equipamento para TC - GS-3268 (925.04 kb)