Assessments - 4, GPA: 3.5
(
)
)
|
Facilidade de uso
ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book. ©2002 ATN Corp. All right reserved. Master power (ON/OFF) switch 100m Infra-red illuminator Proximity sensor Manual focus lens; 5’ to infinity Diopter Control panel Fixator screws Aries MK6600/7700/8700 Elevation Batterycompartment Windage Remote control panel Mounting bracket (mounts to standard U.S. 7/8” weaver rail) Aries MK6650/7750/8750 Remote control Reticle Pattern Selector button APPLICATION The Aries MK6600/6650/7700/7750/8700/8750 night vision weapon scope is a complex computerized system for the observation of objects at low light levels. Containing an onboard computer these scopes are some of the most advanced night vision weapon scopes in the world. The Aries MK6600/6650/7700/7750/8700/8750 consists of the objective lens assembly, ocular lens assembly and the body. The body contains the image intensifier tube assembly with the integrated high voltage power source. The body also houses the electronics for the reticle, the computer console for the “Smart Technology” as well as the battery compartment. The 100M infra-red illuminator is located on the top of the unit. The objective lens protective cover (not shown) is designed to protect the lens from scratches and abrasions. This cover also protects the image intensifier tube from exposure to daylight or other bright light sources. The protective cover acts as a daylight filter, note the pinhole in the center of the lens cap. MASTER POWER SWITCH The Master ON/OFF switch is to be found on top of MK6600/6650/7700/7750/8700/8750. Once the scope’s master power is switched on you can adjust the scope using the buttons on the control box. CONTROL PANEL The control box with the cluster of three buttons on it can be found on the left side of the Aries MK6600/6650/7700/7750/8700/8750. ”SL” button acts as a three-way selection toggle. By pressing it once you will see one of three colored diodes located on the rear side of the control box light up. Make sure to keep both eyes open; your right eye is expected to aim through the scope so that your left eye perceives the changes on the rear side of the control box. “+” and “-” buttons are used to correspondingly increase or decrease adjustments for a chosen function. The three colored led diodes represent the scope function mode. “B” stands for brightness of the light intensifier tube, “R”- for reticle brightness, and “I”- for IR illuminator brightness. Master power switch “+” adjustment button “SL” selection button “-” adjustment button Illuminator brightness LED Reticle brightness LED Brightness LED 3 LIGHT INTENSIFIER TUBE BRIGHTNESS ADJUSTMENT The green led “B” represents the light intensifier tube power ratio. Once this is lit you can adjust the brightness of the light intensifier with the “+” and “-” adjustment buttons. RETICLE BRIGHTNESS ADJUSTMENT By pressing the SL button twice you switch to a yellow “R” diode next to the green one. The yellow diode represents the reticle’s brightness. Adjustments could be easily seen if you look through the Aries MK6600/6650/7700/7750/8700/8750 while pressing “ +” /” -” adjustment buttons. To adjust the brightness of the reticle or to turn it off use the control box buttons located on the side of the unit. Press and hold “+ “or” -” adjustment buttons while the yellow diode is on and see brightness changes looking through the scope. After appropriate level of brightness has been set release the button. INFRA-RED ILLUMINATION By pressing “SL” button three times you can switch to Red diode “I”. Red diode represents 100M infra-red illuminator’s brightness adjustment mode. Adjustments can be easily observed through the Aries scope while pressing” +” /” -” adjustment buttons. Infra-red illuminators, or IR illuminators, are common to night vision. The IR light greatly enhances to the performance of the Aries MK6600/6650/7700/7750/8700/8750 while remaining almost totally invisible to the unaided eye. Power up the Aries scope in a dark environment. Find an object and examine it with IR off, then on. You could observe illumination difference. It is important to remember that the IR illuminator is simply an infra-red light source and like any light source it may loose its effectiveness over long distances. To change the field of coverage from the IR illuminator, focus the beam by turning IR illuminator lens to slightly alter the beam width. Green LED “B” Yellow LED “R” Red LED “I” SLEEP MODE One of the greatest new features that your Smart scope has is the SLEEP mode. This feature has been designed to considerably extend the period of scope’s functioning, to set the scope to memorize your initial settings and endure battery’s life (by settings we mean only digital settings which include brightness of the tube, brightness of the reticle, and magnitude of the IR.) Here is a description as to now the sleep mode functions: The scope will automatically shut down if it does no...