Assessments - 4, GPA: 4.3
(
)
)
|
Facilidade de uso
12. Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturermay cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by The Holmes Group may cause hazards. ALCI (Appliance Leakage Current Interrupter) SAFETY DEVICE: This device provides protection against electric shock due to ground fault currents by automatically shutting off the power. To test the operation of the ALCI Safety Device, switch the heater ON at either the HI or LO setting. Press the TEST button on the ALCI device attached to the plug end of the line cord. The heater and fan should stop operating and the Power Light should be extinguished. Press the RESET button on the ALCI device to resume normal operation of the heater. This devise should not be used as an ON/OFF operation switch. CAUTION: ALTHOUGH THIS DEVICE IS PROVIDED WITH PROTECTION WHICH REDUCES THE RISK OF ELECTRIC SHOCK, THIS PRODUCT SHOULD NEVER BE USED CARELESSLY NEAR WATER. 13. DO NOT use outdoors. 14. To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked. 15. To disconnect heater, turn controls to OFF, then remove plug from outlet. 16. This heater is not intended for use with an extension cord. Plug the cord directly into an appropriate wall receptacle. 17. If the heater will not operate, see specific instructions on Auto Safety Shut-off. 18. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS AUTO SAFETY SHUT-OFF This heater is equipped with a patented, technologically-advanced, safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit. To Reset the Heater: 1. Press the Power/mode button until off is displayed in the LCD screen. 2. Unplug the heater and wait 10 minutes for the unit to cool down. 3. After the 10 minutes, plug the unit in again and operate normally. PRE-OPERATING INSTRUCTIONS 1. Carefully remove your heater from the box. (please save the carton for off-season storage). 2. Place heater on firm level surface. 3. Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps. OPERATING INSTRUCTIONS SETTING THE TIME 1. The LCD Display screen will be flashing 12:00 when you plug the unit into the electrical outlet for the first time. 2. You can set the time by pressing the hour and minute buttons accordingly. The digits will stop flashing 5 seconds after you have set the time and have stopped pressing the hour and minute buttons. OPERATING THE HEATER 1. Press the Power / Mode button once and the display screen will switch from the current time to read FAN. Press the Power / Mode button again and the display will now read LO. Press the Power / Mode button again and the display will then read HI. The heater operates at 750 and 1500 watts in the low or high settings. To turn the unit off, simply press the Power / Mode button for a fourth time and the unit will be turned off. SELECTING DESIRED TEMPERATURE 1. By turning the rotary knob located at the top right side of the heater you will be able to adjust the thermostat. As the rotary knob is turned the temperature will be reflected on the display screen simultaneously. Stop turning the knob when your desired temperature level has been achieved. SETTING THE HEATLOGIC PROGRAM TIME: 1. Press the SET button. The display will switch from the current time to flash the digits 12:00. 2. Press the HOUR and MINUTE buttons until your desired operating time has been reached. The display will return to the current time after you have completed setting the HEATLOGIC time. TO ACTIVATE THE HEATLOGIC PROGRAM TIME 1. To activate your heater at the specified time that has been set, simply press the HEATLOGIC button once. A light in the display screen will be turned on, indicating that the heater is now in HEATLOGIC mode and will turn on automatically at the preset time. PLEASE NOTE: The heater will operate in the HI 1500 watt setting only, when operating in the HEATLOGIC mode. SETTING THE SAFETY SHUT DOWN TIME: In the HeatLogic mode you have the ability to choose the amount of time the heater will operate before automatically turning off. 1. Hold the SET button down for 5 seconds. The number 30 will appear on the display screen indicating the number of minutes the heater is currently set to operate in the HEATLOGIC mode. 2. To change from 30 min, hold SET button and display will change to 45. If you continue to hold th...