Assessments - 3, GPA: 4
(
)
)
|
Facilidade de uso
If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. To prevent serious injury from accidental operation: Turn the Power Switch to its off position and disconnect the Adapter Cord from its electrical supply source before performing any inspection, maintenance, or cleaning procedures. Worklight Set Up Always place the Worklight on a 1. clean, dry, flat, level surface capable of supporting the weight of the Worklight. The work area must be free of direct 2. sunshine and high temperature. Keep children and pets out of the 3. work area. Route the AC/DC Adapter Cord (17) 4. and Cigarette Lighter Adapter Cord (16) along a safe route to reach the work area without creating a tripping hazard or exposing the Cords to possible damage. The Cords must reach the work area with enough extra length to allow free movement while working. General Operating Instructions To Charge the Battery Pack Using the AC/DC Adapter: To charge the Battery Pack (12) of 1. the Worklight, open the Charging Socket Cover (11) on the tool and insert the AC/DC Adapter Cord (17) into the tool’s Charging Socket (7). Make sure the Power Switch (10) is in its “OFF” position throughout the charging process. Then plug the AC/ DC Adapter into the nearest 120 volt, grounded, electrical outlet. IMPORTANT: 2. The initial charge time for the Battery Pack is 10 hours. Thereafter, the charge times are 6 hours. Do not overcharge the Battery to avoid damage to the Battery and/or AC/DC Adapter. The Battery Indicator Light on the 3. Worklight will illuminate as follows: Battery needs charging:• Right side LED illuminates RED. Battery is charging:• Left side LED illuminates RED. Battery is fully charged: • Left side LED illuminates GREEN. When finished charging, unplug the 4. AC/DC Adapter from its electrical outlet. Then unplug the Cord from the Charging Input Port of the Worklight. (See Figure A.) POWER SWITCH (10) CHARGING SOCKET COVER (11) FIGURE A AC/DC ADAPTER CORD (17) OR CIGARETTE LIGHTER ADAPTER CORD (16) To Charge the Battery Pack Using the Cigarette Lighter Adapter: Prior to recharging, allow the battery 1. to cool completely. To charge the Battery Pack (12) of 2. the Worklight, open the Charging Socket Cover (11) on the tool and insert the Cigarette Lighter Adapter Cord (16) into the tool’s Charging Socket (7). Make sure the Power Switch (10) is in its “OFF” position throughout the charging process. Then plug the Cigarette Lighter Adapter into a 12 VDC vehicle cigarette lighter receptacle. IMPORTANT:3. The initial charge time for the Battery Pack is 10 hours. Thereafter, the charge times are 6 hours. Do not overcharge the Battery to avoid damage to the Battery and/or AC/DC Adapter. The Battery Indicator Light on the 4. Worklight will illuminate as follows: Battery needs charging:• Right side LED illuminates RED. Battery is charging:• Left side LED illuminates RED. Battery is fully charged: • Left side LED illuminates GREEN. When finished charging, unplug the 5. Cigarette Lighter Adapter from its lighter receptacle. Then unplug the Cord from the Charging Input Port of the Worklight. (See Figure A.) Turning the Worklight on and off: To turn on the Worklight, press the 1. Power Switch (10) to its “ON” position. To turn off the Worklight, press the Power Switch again to its “OFF” position. (See Figure A.) The Worklight is designed to operate 2. (on a fully charged Battery Pack) for approximately 6 hours before recharging is required. When finished using the Worklight, 3. make sure to store the tool in a clean, dry, safe location out of reach of children and other unauthorized persons. Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Before performing any inspection, maintenance, or cleaning procedures: Turn the Power Switch (10) of the Worklight to its “OFF” position. Unplug the tool’s AC/DC Adapter (17) or Cigarette Lighter Adapter (16) from its electrical outlet. Then allow the tool to completely cool. To prevent serious injury from EQUIPMENT failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Inspection, Maintenance, and Cleaning BEFORE EACH USE:1. Inspect the general condition of the Worklight. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts and any other condition that may affect its safe operation. BATTERY PACK REPLACEMENT:2. This Battery Pack is NOT replaceable. CIGARETTE LIGHTER ADAPTER 3. FUSE REPLACEMENT: A faulty Cigarette Lighter Adapter typically indicates a blown Fuse. To replace the Fuse, unscrew and remove the Outer Fuse Cap. ...