Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Inspection and repairs Before use, check the appliance for damaged or defective parts. Check for breakage of parts, damage to switches and any other conditions that may affect its operation. The following safety symbols are marked on your spotlight: Warning! To reduce the risk of injury, the user must read the instruction manual. Warning! Do not touch the lens as it becomes very hot during operation and remains hot for several minutes after the spotlight is switched off. Allow the spotlight to fully cool down before storage or charging. Keep combustible materials away from spotlight lens. Extreme heat can cause fires. Never place the light face-down on any surface when it is switched on or cooling. Do not leave the spotlight unattended. Keep children and animals away from the work area. Inspect the lens for damage following impact or if the spotlight is dropped. Do not operate without the lens in place or with a damaged lens. The lens is manufactured from glass. The lens may crack or break if subject to an impact. If the lens is damaged it must be replaced by manufacturers original parts. Wear gloves as sharp edges may cause injury. Never look directly into the light or shine the light into another person's eyes. Do not immerse spotlight in water. FEATURES This appliance includes some or all of the following features: 1. Quartz halogen bulb 2. Hanging loop 3. Trigger lock 4. Pistol grip 5. On/off trigger switch 6. 12 Vdc power lead 7. 12 Vdc accessory plug 8. 12 Vdc battery clamps USE Power source requirements The power source must provide 12 Vdc and must be able to supply the necessary current to operate the load. 9 ENGLISH Warning! The spotlight must be connected only to batteries with a nominal output voltage of 12 volts. The spotlight comes equipped with a 12 Vdc accessory plug (7) and/or battery clamps (8) for connection to a dc power source. Always attach the connector end of the 12 Vdc battery clamp cable (8) to the 12 Vdc power lead (9) before attaching the battery clamps (8) onto the battery terminals. Connecting to a power source using the 12 Vdc accessory plug (7) Make sure the spotlight is turned off, the trigger lock (3) is in the down position (locked) and that no flammable fumes are present in the area. Connect the spotlight to the power source by inserting the 12 Vdc accessory plug (7) firmly into the accessory outlet of a vehicle or other dc power source. Move the trigger lock (3) up to the unlocked position. Press the On/Off trigger switch (5) to turn the spotlight on. To lock the trigger switch (5) in the on position, press the trigger switch (5) and push the trigger lock (3) down. To shut the spotlight off, switch to the unlocked position and press the trigger. Connecting to a power source using the cables Use the cables and connect the appliance directly to the 12 Volt power source as follows: Warning! Explosive gas may be vented from batteries when charging and under extreme conditions battery leakage may occur. Ensure the area is well ventilated when connecting the spotlight to a battery. Never allow the connector end of the 12 Vdc battery clamp cable (8) to touch the battery terminals. This could cause damage to the appliance and/or create a sparking/explosion hazard. Check the polarity of the battery terminals before connecting the spotlight. Make sure the spotlight is turned off, the trigger lock (3) is in the down position (locked) and that no flammable fumes are present in the area. Connect the red battery clamp (8) to the positive terminal of the battery. Connect the black battery clamp (8) to the negative terminal of the battery. Make sure that all connections between the battery clamps (8) and the battery terminals are secure. Move the trigger lock (3) up to the unlocked position. Press the On/Off trigger switch (5) to turn the spotlight on. To lock the trigger switch (5) in the on position, press the trigger switch (5) and push the trigger lock (3) down. To shut the spotlight off, switch to the unlocked position and press the trigger. Warning! Loose connectors may cause overheated wires and melted insulation. Using the hanging loop The hanging loop (2) may be used to hang the spotlight from a suitable location. Warning! When using the hanging loop and the spotlight is turned on keep combustible materials away from the spotlight lens. Extreme heat can cause fires. MAINTENANCE Your Black & Decker tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance or cleaning on the appliance, unplug the appliance. From time to time wipe the appliance with a damp cloth. Do not use any abrasive or solvent-based cleaner. Do not immerse the appliance in water. Replacing the fuse in the vehicle dc accessory plug Remove the cap by turning it counter clockwise. Remove the centre pin and the spring. Remove the fuse. Fit a new fuse of t...