Assessments - 2, GPA: 3.5
(
)
)
|
Facilidade de uso
Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1. SAVE THESE INSTRUCTIONS BATTERY PACK/CHARGER The battery pack and charger are not included with your worklight. They are both sold separately. When purchasing, use the following information: MODEL NO. BATTERY PACK CHARGER 973.113911 item No. _911375 item No. _911041 (1323517 or 1323903) (1425301) BATTERY PACK The battery pack for your worklight has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until light on front of charger changes from red to green. Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (operating worklight followed by recharging) for batteries to become fully charged. CHARGING BATTERY PACK See Figure 1. [] Use only the recommended battery pack and charger with your worklight. [] Make sure power supply is normal household voltage, 120 volts, 60 Hz, AC only. [] Connect charger to power supply. [] Place battery pack in charger aligning raised rib on battery pack with groove in charger. See Figure 1. [] Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charger. [] Normally, the red LED on charger will come on. This indicates charger is in fast charging mode. [] Red LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in trickle charge mode. Note: Green LED will remain on until battery pack is removed from charger or charger is disconnected from power supply. BATTERYPACK SHOWNIN CHARGER CHARGER [] If both yellow and green LED come on, this indicates a deeply discharged or defective battery pack. Allow battery pack to remain in charger for 15 to 30 minutes. When battery pack reaches normal voltage range, red LED should come on. If red LED does not come on after 30 minutes, this indicates a defective battery pack and should be replaced. [] After normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack. [] The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. [] Do not place charger and battery pack in an area of extreme heat or cold. It will work best at normal room temperature. Note: Charger and battery pack should be placed in a location where the temperature is more than 50°F but less than 100°R [] When batteries become fully charged, unplug charger from power supply and remove the bat tery pack. iNFORMATION FOR RECHARGING HOT BATTERY PACK When using your worklight continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert battery pack in charger. If green LED continues to remain on, return battery pack to your nearest Sears Repair Center for checking or replacing. Note: This situation only occurs when continuous use of your worklight causes the batteries to become hot. It does not occur under normal circumstances. Refer to "CHARGING BATTERY PACK" for normal recharging of batteries. If the charger does not charge your battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears Repair Center for electrical check. REDLEDON INDICATES FASTCHARGINGMODE GREENLEDON AFTERFASTCHARGING CYCLE,iNDICATESFULLYCHARGEDBATTERY PACKANDIN TRICKLECHARGEMODE. YELLOWANDGREENLED8 ON INDICATESDEEPLY Fig. 1 LED FUNCTIONS OF CHARGER LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK: [] Red LED on = Fast charging mode. [] Green LED on = Fully charged and in trickle charge mode. [] Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of or below normal temperature range. [] Yellow and Green LEDs on = Deeply discharged or defective battery pack. [] No LED on = Defective charger or battery pack. CAUTION: To prevent damage to battery pack, remove battery pack from charger immediately if no LED comes on. Return battery pack and charger to your nearest Sears Service Center for checking or replacing. Also, if you are removing battery pack from charger and no LEDs are on, return both battery pack and charger to your nearest Sears Service Center. Do not insert another battery pack into charger. A damaged charger may damage a battery pack. TO INSTALL/REMOVE BATTERY PACK See Figure 2. [] Use only the recommended battery pack with your worklight. ,A WARNING: Do not install battery pack to your worklight until you have read...
Este manual também é adequado para os modelos :Iluminação - 315.113911 (808.35 kb)