Assessments - 2, GPA: 5
(
)
)
|
Facilidade de uso
This light has been designed for painting, wallpapering or for any project, indoors or outdoors, where true color rendition is desired. This light also eliminates unwanted shadows or glares, making painting and wallpapering easier while providing professional results. What you need • Screwdriver • 3 Wire grounded extension cord What’s included • Fully assembled unit (A) • (2) 300 watt quartz halogen bulbs (B) What to know INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS. READ ALL INSTRUCTIONS. Warning: To reduce the risk of FIRE, ELECTRIC SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO PERSONS: • Unplug and allow to cool before replacing bulb. • Lighted lamp is HOT! • Do not remain in light if skin feels warm. • For indoor and outdoor use. • cULus Listed for wet location use. • Fixture must be connected to a 120 Volt, 60 Hz power source. Any other connection voids warranty. • Keep away from flammable objects. • The bulb and fixture get extremely hot during use. Always unplug the light and let it cool 5 minutes before attempting to touch the fixture. • Do not touch hot lens, guard, or enclosure. • Bulb gets HOT quickly! Only contact switch/plug when turning on. • The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes. • Do not operate the unit with a missing or damaged wire safety guard, safety glass lens (lamp containment), or UV filter. A B PHL300 325-1576.qxd 8/22/06 4:13 PM Page 3 • Do not operate the unit with a missing or damaged wire safety guard, safety glass lens (lamp containment) or UV filter. • Do not direct the light at persons or look directly at lighted fixture. • Use only with a 300 watt or smaller bulb. Installing a bulb of a higher wattage could create a fire hazard. Use of a higher wattage bulb will void the warranty. • Never touch the bulb with your bare hands. Oil from your skin can cause premature failure. Always handle the bulb with gloves or a soft cloth.withple I • If lens is replaced, use only a diffused tempered safety glass of equal thickness. • For maximum bulb life, position light so that the quartz halogen bulb remains within 4 degree of horizontal. • Disassembly of your fixture will void the warranty. NOTE: When using outdoor use portable lamps, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury, including the following... • Use only with three wire extension cords that have three-prong gorunding plugs and that are suitable for outdoor use, such as cords marked SW, SW-A, SOW, SOW-A, STW, STW-A, STOW, STOW-A, SJW, SJW-A, SJOW, SJOW-A, SJTW-A, SJTOW, SJTOW-A and grounding receptacles that accept a three-prong plug. When the fixture is used in wet locations, Ground Fault Circuit Interruption (GFCI) protection must be provided on the circuit(s) or outlet(s) to be used. Receptacles are available having built-in GFCI protection and are able to be used for this measure of safety. NOTE: Deviation from the assembly instructions may result in a risk of fire or electric shock. SAVE THESE INSTRUCTIONS. Installing the bulb Step 1: Loosen the screw in the front of the handle located on top of the fixture. Step 2: Open lens cover for easy access to the bulb. Step 3: Remove bulb and CAUTION sheet from housing. Unpack bulb, being careful not to touch it with your bare hands (see caution sheet). Step 4: Using gloves or a soft cloth, gently press the bulb to one side of the socket as indicated on the metal reflector and insert the opposite end into the other side of the socket. Reverse this procedure to remove the bulb. Step 5: Close the lens cover and tighten the screw. Note: Should the light not turn on when power is applied, unplug the unit, then check that the bulb is properly seated in the sockets. Spare Bulb: A spare 300 watt halogen bulb is located in the bulb storage compartment located below and behind the switch/receptacle box. Remove the cap at the end of the storage compartment to access the bulb. Always handle the bulb with gloves or a soft cloth. Call for customer service and/or missing or damaged parts (800-334-6871) 3 ENGLISH PHL300 325-1576.qxd 8/22/06 4:13 PM Page 4 ENGLISH How to use The fixture is packed in the compact storage position. Remove the fixture from the carton. Loosen knobs on the sides of the fixture and swing the fixture up so that the wire lens guard is directly above the closed (curved) portion of the tubu- lar steel stand. Retighten the knobs. (Reverse this procedure to fold down the light fixture for convenient, compact storage.) Plug the female end of your 3 wire grounded extension cord into the receptacle located in the back of the light fixture and then plug the male end of your exten- sion cord into any standard grounded 120 Volt wall receptacle. Push the red on/off/dimmer switch on ...