Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
Secure with screw Secure by placing one (1) Phillips head screw (supplied) into rear of Handle Assembly. Tighten with screwdriver until secure. 1. 2. 1. 2. Plan activities to give carpet time to dry. Remove easily moved furniture (chairs, lamps, coffee/cocktail tables, etc.) from room if needed. Vacuum carpet thoroughly. Decide where to begin — and end — your job. Clean in 3’ X 4’ sections, starting in areas farthest from exit. Plan to leave a path open to empty soiled water and refill cleaner. Carpeting will dry in three to four hours, depending on carpet style and air circulation in room. A floor fan speeds drying. Replace furniture on damp carpeting by placing waxed paper under legs until floor dries completely. Remove the Clean Water Tank by lifting it straight up, then away from the Lower Body. Using the Formula Measuring Cap, add two (2) capfuls of BISSELL® Fiber Cleansing Formula™ to the Clean Water Tank. Add 1/2-gallon of hot (NOT boiling) tap water. Fill only to fill line – do not overfill. Replace & turn Formula Measuring Cap clockwise until secure. Place Clean Water Tank on Body. Rotate Quick Release Cord Wrap™ and plug in. Turn Power Switch [back of Lower Body] to ( ) ON. If cleaner starts when first plugged in, switch cleaner OFF ( ) until ready for use. How to use your BISSELL QuickSteamer How to begin 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. Getting ready Tip: Always vacuum thoroughly before you deep clean. If possible, move larger furniture to an area you will not be cleaning. 1. 6. How to use your BISSELL QuickSteamer How to begin 1. 2. 3. 4. 5. 6. 1. 2. 3. 4. 5. 6. Getting ready Tip: Always vacuum thoroughly before you deep clean. If possible, move larger furniture to an area you will not be cleaning. 1. 6. WARNING: Use only BISSELL Fiber Cleansing Formula™ or Floor Cleansing Formula™ in your QuickSteamer.™ Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners orsolvent-based soil removers should not be used. These products may react with theplastic materials used in your QuickSteamer,™ causing cracking or pitting. Formula Measuring Cap Unscrew to Remove Power Switch Pre-Treating (Optional) Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. Spray soiled area with BISSELL® Tough Stain PreCleaner.™ Use a stiff-bristled brush to work formula into carpet pile. Wait 3 -5 minutes before deep cleaning. ) ON. Tip: Deep cleaning spots, spills and high traffic areas on a regular basis can prolong carpet life. Tip: Deep cleaning carpeting regularly can reduce dust and allergens in your home. *Available with select models only. If your QuickSteamer did not come so equipped, you may call BISSELL Consumer Services at 1-800-237-7691 to order one. You can also visit the BIS- or other Bare Floor Tool (select models only) Dirty Water Tank 7. 1. 2. 3. Deep Cleaning 1. 2. 4. 3. 5. 6. 7. 8. Turn Power Switch [back of Lower Body] to ( With foot, press the Detent Pedal on right side of Lower Body. Depress Trigger to spray cleaning solution. Do not overwet. Repeat motion over same area without depressing Trigger. Repeat Steps 3 and 4 until no more dirt can be removed. Continue to clean entire carpet, working in 3’ x 4’ sections. Empty the Dirty Water Tank when dirty water reaches the full line, or when the Clean Water Tank is empty. If Floor Nozzle stops spraying, turn Power Switch to OFF ( ) and check water and cleaning solution levels. Refill if needed. Attaching the Bare Floor Tool SELL website: NOTE: Your QuickSteamer is not recommended for cleaning wood floors. • Use only BISSELL® Floor Cleansing Formula™ on no-wax floors. Never use BISSELL Fiber Cleansing Formula™ carpet cleaners on bare floors. • Sweep or vacuum before starting. • Remove old wax before cleaning. • Leave an exit path for yourself. • Allow at least 1/2 hour drying time. Attaching the Bare Floor Tool Continued* Cleaning Bare Floors *Available with select models only. Remove Dirty Water Tank. Remove Brush by depressing tabs on the Cross Action™ Brush outward with thumbs until the Brush loosens. Add Bare Floor Tool underneath the Floor Nozzle by sliding notches and tabs into the opening until it is secure. Make sure tabs on the Bare Floor Tool snap over front lip of Floor Nozzle. Replace empty Dirty Water Tank. Empty and rinse Clean Water Tank. Using the Formula Measuring Cap, add two (2) capfuls of BISSELL® Floor Cleansing Formula™ to the Clean Water Tank. Add 1/2-gallon of hot (NOT boiling) tap water. Fill only to fill line – do not overfill. Turn Formula Measuring Cap clockwise until secure. Rotate Quick Release Cord Wrap™ and plug in. Turn Power Switch [back of Lower Body] to ( ) ON. Slowly move QuickSteamer back and forth over soiled surface one time while depressing Trigger. Do not overwet. Repeat motion over same area without depressing Trigger. Repeat Steps 1 and 2 until no more dirt can be removed. If Floor Nozzle...