Assessments - 3, GPA: 3.3
(
)
)
|
Facilidade de uso
• After the unit is installed, check whether the brake indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the faceplate does not hit the lid when closing — 11 — English Connecting Wires to Terminals Connector Function Guide Fuse (10A) Pin Numbers for ISO Connectors Cable Color Functions External Power Connector A–4 A–5 A–7 A–8 Yellow Blue/White Red Black Battery Power Control Ignition (ACC) Earth (Ground) Connection Speaker Connector B–1 B–2 B–3 B–4 B–5 B–6 B–7 B–8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) — 12 — 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 ANT CONT TEL MUTE Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input (Accessory3) Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Motor antenna control wire antenna. Do not let the wire come out from the tab. Not Used Antenna Conversion Adaptor (ISO–JASO) Antenna Cord (ISO) Depending on what antenna you are using, connect either to the control terminal motor antenna, or to the power terminal the booster amplifier of the film- Connecting Wires to Terminals 2WARNING Connecting the ISO Connector (see p.12) The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector connected to anything, while the A-7 pin (red) constant power supply (or both the A-7 (are connected to the constant power supply). Unit Vehicle Ignition cable (Red) A–7 Pin (Red) Battery cable (Yellow) A–4 Pin (Yellow) When the connection is 3 above, the unit's power be linked to the ignition For that reason, always off the unit's power To link the unit's power (ACC...red) Installation ¦ Installation Firewall or metal support Make sure that the unit is installed securely in place. If the unit unstable, it may malfunction (eg, the sound may skip). Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) ignition key. — 13 — 13— 13 — —— Installation English ¦ Removing the hard rubber frame ¦ Removing the Unit 1 Refer to the section “Removing the hard rubber frame” and then 1 Engage the catch pins on the removal tool and remove the two remove the hard rubber frame. locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 Remove the screw (M4.8) on the back panel. Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. 3 Insert the two removal tools deeply into the slots on each side, as shown. Screw (M4X8) (commercially available) 4 Lower the removal tool out the unit halfway while toward the bottom, and pull pressing towards the inside. Accessory2 Removal tool Be careful to avoid injury from the catch pins 5 Pull the unit all the way out with your hands, being The frame can be removed from careful not to drop it. — 14 — 14— 14 — —— Troubleshooting Guide What might seem to be a malfunction in your unit may ? No sound can be heard, or the volume is low. just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . No ACC position on vehicle ignition. . Connect the same cable to the ignition as the battery cable. ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. ? The faceplate does not open or close. . The faceplate is incorrectly attached. . Reattach the facepla...
Este manual também é adequado para os modelos :Jogadores - KRC-21SA (648.1 kb)