Assessments - 4, GPA: 4.8
(
)
)
|
Facilidade de uso
¦ The correct recording level is automatically set by the ALC (Automatic Level Control) function, and is not affected by the VOLUME control on the Unit or by the use of sound effects. ¦ Two small tabs on the back of the cassette tape, one for side A and one for side B, can be removed to prevent accidental erasure or recording. ¦ To record on a cassette with the tabs removed, you must cover the holes with adhesive tape as shown. Notes: • Use normal tapes (not metal or CrO2 tapes) for recording. • At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. • If a recorded tape you make has excessive noise or static, the Unit may have been too close to a TV during the recording. Either turn off the TV or increase the distance between the TV and the Unit. Recording from the Radio n 1. Press the ¤ STOP/EJECT button to open the cassette holder. n 2. Insert a blank or erasable cassette tape with the exposed side facing upward as shown below and wind past the leader tape. + Forward direction nn 3. Close the holder gently until it clicks. 4. Tune in to a radio station. n 5. Press the ¦ REC button on the Unit. The PLAY button is pressed at the same time, the “REC” indicator lights up, and the Unit begins recording. • The tape is recorded and then stops when it reaches the end. To pause the recording, press the 8PAUSE button on the Unit. To cancel pause, press the 8 PAUSE button again. Recording continues from the point where it was paused. To stop recording, press the ¤ STOP/EJECT button. To remove the tape, stop the tape, and press the ¤ STOP/ EJECT button again to open the cassette holder. 7 EnglishEnglish Recording an AM station (BEAT CUT) When recording an AM broadcast, beats may be produced which are not heard when listening to the broadcast. If this happens, you can use the BEAT CUT function. Switch the BEAT CUT switch on the back of the Unit from the NORM-1 to 2 or 3. Note: In regular use, the BEAT CUT switch should be set to the NORM-1 position. Recording from the CD The CD Player can be started with the Cassette Deck for synchronous recording and everything on the CD recorded onto the tape in the order it is on the CD. n 1. Insert a cassette tape in the Cassette Deck and wind past the leader tape. n 2. Load a CD. nn 3. Press the CD 6 button. 4. Press the 7 button to stop the CD. • You can check the number of tracks and the total playback time of the CD on the display. (See page 6.) n 5. Select the Repeat mode of the CD if desired. To select the Repeat mode ( or ALL), press the REPEAT button on the Remote Control. n 6. Choose whether to have approx. four seconds of blank tape between tracks. If you want the blank section, skip this step. If you do not want the blank section, perform the following operation on the CD Player. • Press the CD 6 button twice. n 7. Press the ¦ REC button on the Unit. The PLAY button is pressed at the same time, the “REC” indicator lights up, and the synchronous recording begins. • The tape is recorded and then stops when it reaches the end. • To continue recording to the other side of the tape, perform the following steps. 1. Reverse the cassette tape and wind past the leader tape. 2. Press the CD 6button and then press the ¦REC button. Then, the synchronous recording begins from the beginning of the last track that was stopped at the end of the first side of the tape. To stop recording, press the ¤ STOP/EJECT button. To remove the tape, stop the tape, and press the ¤ STOP/ EJECT button again to open the cassette holder. Notes: • If the CD reaches its end before the tape, the tape will continue to run until stopped. Press ¤ STOP/EJECT button to stop the tape. • During synchronous recording, the CD 6, 4, and . buttons for the CD Player do not function. • If you press the ¦ REC button during play the CD, recording will start from the beginning of the track being played. ¦ nnUsing the Sleep Timer SLEEP Use the Sleep Timer to turn the Unit off after a certain number of minutes when it is playing. By setting the Sleep Timer, you can fall asleep to music and know that your Unit will turn off by itself rather than play all night. ¦ You can only set the Sleep Timer when the Unit is on and a source is playing. n 1. Play back a CD, tune in to a desired station, or play back a tape. n 2. Press the SLEEP button on the Remote Control. The “SLEEP” indicator lights up. n 3. Set the length of time you want the source to play before shutting off. • Each time you press the SLEEP button, it changes the number of minutes shown on the display in this sequence: = 30 = 60 = 90 = 120 = Cancelled = (back to the beginning) The display will stop blinking after 5 seconds and return to the display before you set the Sleep Timer. The Unit is now set to turn off after the number of minutes you have set. To Confirm the Sleep Time When the SLEEP button is pressed, the remaining sleep time is displayed. After 5 seconds the original display returns. To Cancel the SLEEP Timer Setting P...