Assessments - 1, GPA: 3
(
)
)
|
Facilidade de uso
NOTE: Where passage through a wall, or partition of combustible construction is desired, theinstallationshallconformto CAN/CSA-B365. (if in Canada) I nsid e Co rn er De ta il FixedClosedOpenableOpenableFixedClosed V = Vent terminal = Air supply inlet = Area where terminal is not permitted A 17 18 DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. INSTALL VENT AT CLEARANCES SPECIFIED BY THE MANUFACTURER Mobile home installation should be done in accordance with the Manufactured Home and Safety Standard (HUD), CFR 3280, Part 24. DO NOT INSTALL IN SLEEPING ROOM WARNING KEEP COMBUSTIBLES AWAY FROM FLUE OUTLET. CAUTION CAUTION THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED. 3' Keep combustible materials such as grass, leaves, etc. at least 3 feet away from the point directly under the vent termination. WARNING Venting Ash Pan Removal and Reattachment Fig. 29 Fig. 30 Fig. 31 Fig. 32 Fig. 33 Maintenance -Emptying Ashes Soot and Fly Ash Ash Pan Removal and Reattachment Fig. 29 Fig. 30 Fig. 31 Fig. 32 Fig. 33 Maintenance -Emptying Ashes Soot and Fly Ash Figure 29 Open side doors. Figure 30 Release spring latches on the right and left side of the ash pan. Figure 31 Slide ash pan forward enough to lift with center handle. Empty ashes and reinstall ash pan. Ashes shouldbeplacedin ametalcontainerwith a tight fitting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, well awayfromallcombustible materials,pending final disposal. If ashes are disposed of by burial in soil or otherwiselocallydispersed,theyshould beretained in the closed container until all cinders have thoroughly cooled. Figure 32 Inspect the gasket rope for damage. Replace if necessary. Figure 33 Insert spring latch front hooks into the ash pan side slots. Push both latches to the rear at the same time to latch. The products of combustion will contain small particles of fly ash. The fly ash will collect in the exhaust venting system and restrict the flow of the flue gases. Incomplete combustion, such as occurs during startup, shutdown, or incorrect operation of the room heater, will lead to some soot formation which will collect in the exhaust venting system. The exhaust venting system should be inspected at least once each year to determine if cleaning is necessary. When removing the ash pan to empty ashes, you will note a build up of ash fines behind the ash pan. This space behind the ash pan was designed to allow the fines to fall out of the vertical heat exchangers and collect where they are easily cleaned out, rather than going into the flue pipe where it would be difficult to clean. These fines should not be allowed to build up. They may not allow the ash pan to be seated into its gasket properly.NOTE: If an extreme amount of force is required to snap the latch on one or both sides oftheash pan,theareabehindtheashpan should be checked for ash fine build up. 19 20 Opening and Closing the View Door Opening: The view door must be opened for cleaning of the glass and scraping of the burn pot. This should be done with the unit off and cool, in most cases. Although the glass can be cleaned and burn pot scraped while the unit is at low burn. 1. Using scraper as shown in Fig. 34and 35, lift the door latch forward and up. 2. Swing the door open to the left, stopping the swing when resistance is felt. Forcing the door open further then was designed may cause damage to the door or it's hinges. CAUTION Do not put excessive downward pressure on the latch end of the door while in the open position. If the door is going to be opened for an extended period of time, it is suggested that it be removed (see Fig. 36) and set safely aside. 3. Inspect the door gasket and glass gaskets for worn or missing pieces. Replace if necessary. (Fig. 37) Closing: When closing the door, always hold the door latch all the way up until it has caught the receiving bolt. Then push the latch downward and back until the door is fully seated. See Fig. 35. Removing View Door: To remove the view door from the stove, hold the door by the bottom and lift upward off of the hinge pins.See Fig. 36. Inspect the door gasket.See Fig. 37. REPLACE GLASS WITH CERAMIC GLASS ONLY. Fig. 34 Fig. 35 Fig. 36 Fig. 37 Receiving Bolt WARNING Door latch may be hot! Maintenance - Cleaning Glass on View Door 21 Burn Pot Cleaning and Maintenance 1. Scrape the top holed surface and sides of the burn pot.(Fig 38) It is not necessary to completely remove all material from the burn pot. The excess will be pushed out during the next use. 2. Loosen the (2) wing thumb screws on the lower front angle of the burn pot. (Fig. 38) 3. Lift off the clean-out cover (Fig.39) to open the bottom clean-out chamber. (Fig.40) 4. Clean ash buildup from inside the chamber while cover is off. Use the scraper to tap on the top front edge of the burn pot. This w...