Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
Leave at least 750 mm clearance above the hotplates. The appliance should be located on a level surface. The two front feet can be adjusted as required. To ensure that your appliance is standing level adjust the two front feet by turning clockwise or counterclockwise until the product is in firm contact with the floor. Installation of gas cookers ^Before your appliance is connected to the gas supply, check the ensure that the gas category and pressure specifications shown in the data plate corresponds with your gas supply If necessary call authorized service for adjusting to gas category *This appliance shall be installed in accordance with the regulations in force and only used in a well ventilated space. Read the instructions before installing or using this appliances. In the interest of safety this appliances must be installed and/or serviced by a competent person as stated in the gas safety regulations current editions * Please refer to the data plate for details about gas supply and pressures. * The appliance must not be installed in a room without a window or other controllable opening. If is installed in a room without a door which opens directly to tohe outside, a permanent opening is required. The air circulation should be 2 m3/h per kW of burners. Connection of the gas hose to the oven Convenient position is selected by interchanging the hose nozzle and plug according to the location of the main gas inlet valve. If you make a connection with a flexible metal hose , locate a seal between the main gas pipe. The inner diameter of the flexible hose, which the butane hose nozzle is connected, should be 6mm for the house-type gas tubes. The inner diameter of the flexible hose, which the natural hose nozzle is connected, should be 15mm. The hose should tightly be fitted to the hose nozzle by squeezing with a clamp.The plastic hose end is soaked in hot water for one minute to soften and inserted fully into the hose nozzle. The clamp is fastened securely by a screw driver. The other end of the hose is connected to the gas valve with the same operation. The hose should be replaced before its last expiry date. P^g Hose nozzle Caution! j :: Make the oven connection to the gas inlet valve, the hose length must be short and be sure that there is no leakage. The hose used should not be longer than 125 cm for safety. Connection of the gas hose to the oven Convenient position is selected by interchanging the hose nozzle and plug according to the location of the main gas inlet valve. The plastic hose end is soaked in hot water for one minute to soften and inserted fully into the hose nozzle. The clamp is fastened securely by a screw driver. The other end of the hose is connected to the gas valve with the same operation Gas leakage control During control, be sure that the control knobs are closed and the gas inlet valve is open. Apply soap bubbles to the connections for leakage control. In case leakage exists, buble will appear. In such case, check the gas connection immediately Do not control gas leaks by using fire. Caution! Never use lighter or match flame, for controlling the gas lackage. Cbmp Hose nozzle and elbow types for Natural gas and Butane/propane s Part 3: Technical specifications 1. Burners 2. Conlrol panel 3. Front door 4. Handle 5. storage compartment 6. Tray 7. Grill shelf 8. Integral air oven There may also be plate location other than the ways shown in the figures The fast radian, extended and dual plates burn with that brillant light when they are first ON A rapid heating solid plates are as denoted by a red spot in the centre of the plate. The voltage, frequency and maximum powers shown in the rating label Conventional cookers Multi-function cockers Fan assisted cookers Grill wattage 11002300 1100/2300 11002300 Ovenwattaoe 2400 W 2400 W 2400 W Turbo waflaqe - 2100 W - Turbo motor wattaqe - 38W/2800 rpm 38 W/2800 rpm Lamp 15VW25W 15W/25W 15W/25W External dimensions H: 850 W: 600 D:600 H: 850 W600 D: 500 H: 850 W:600 D:600 1, a 140 1200 W Radian plate 2 0 140 1200 W Fast radian plate 0 1 SO 1700 W Radian plate 4. 0 180 1800 W FasL radian plale ■> 0 170x265 900-2400 W Extended plate Ç. 0 180 2000 W Rapid plate 7, a 145 1000 WSolid plate 8. 0 145 1500 W Rapid plate 9. a 180 1500 WSolid plate 10.0 80 450 W solid plate 11. 0 1S0 1000 WSolid plate 12. Rapid burner 2.9 kW 13. Semi rapid burner 2.0 kW 1 4. Auxiliary burner 1.0 kW 1 5.0 220 2000 W Fast solid plate 16. 0 120x180 700-1700 W dual plate © ® © © © ® © ©® 0© ® © @„© © ® © ©0 0® o© ©o m ©(0 0© 0© ©0 ©o o© ©o 0© ©0 0© o© ©0 o© ©0 0© ©XD Part 4: Operating the top burners To obtain maximum efficiency A correct use to burner results in gas saving and better out put. Therefore we recommend to use saucepans whose base completely cover the ■flames. Four saucepans with much smaller diameters to be put auxiliary burner,use the pan support adaptor. 1S cm If your coo...
Este manual também é adequado para os modelos :Placa - CE 68100 (1.28 mb)
Placa - CM 64220 (1.28 mb)
Placa - CM 68201 (1.28 mb)
Placa - CM 68201 C (1.28 mb)