Log:
Assessments - , GPA: ( )

Instruções de Operação England's Works, Modelo 24-JC

Fabricante : England's Works
Arquivo Tamanho: 64.12 kb
Arquivo Nome : 17a42efe-af2e-4e8f-89ee-4ac356b1a772.pdf

Língua de Ensino: en

O documento está colocado, por favor, espere
O documento está colocado, por favor, espere

Facilidade de uso


Visit our web page at for helpful information, frequently asked questions, parts & accessory orders and more. NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489. CAUTIONS AND WARNINGS: READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION CAUTION: This unit must be installed in accordance with these instructions and must comply with local building and fire codes. Failure to do so could result in a chimney or house fire, property damage, bodily injury or even death.. Keep children, furniture, fixtures and all combustibles away from any heating appliance. DO NOT INSTALL THIS UNIT IN A MOBILE HOME OR DOUBLE WIDE! DO NOT INSTALL THIS UNIT IN A PRE-MANUFACTURED FIREPLACE! FOR MASONRY FIREPLACE INSTALLATION ONLY. This product contains a catalytic combustor, which needs periodic inspection and replacement for proper operation. It is against the law to operate this wood heater in a manner inconsistent with the instructions in the manual or if the catalytic element is deactivated or removed. Our catalytic stoves are designed to burn seasoned, dry wood. 24-JC, 50-SHW20 and 50-TRW20 COMPLIANCE STATUS TYPE OF FUEL WOOD EMISSION RATE 2.1 GRAMS PER HOUR OVERALL EFFICIENCY 83.04% HEAT OUTPUT TEST RANGE 7,200 TO 28,600 BTU/HR EPA CERTIFICATE NUMBER 267 THIS UNIT IS CERTIFIED TO EPA PHASE II STANDARDS Text Box: Text Box: Rev. 1/06 Text Box: England’s Stove Works highly recommends the use of smoke detectors and Carbon Monoxide detectors with any hearth product, including this unit. Follow all manufacturer’s instructions when using smoke or Carbon Monoxide detectors. SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS FOR RESTRICTIONS AND INSPECTIONS IN YOUR AREA. SECTION I: FLUE SYSTEM This stove is designed to install into a masonry fireplace. The minimum opening is 28” wide x 24” high x 16” deep and you must have at least fourteen inches (14”) of hearth extending from the fireplace face. Flue Size Needed: The proper flue size is normally determined by the inside diameter of the opening on the unit, which in this case is eight inches (8”). Therefore, the connector pipe should be the same size or larger and never less in diameter than the opening on the stove. The area of the chimney liner in square inches must also be equal to or larger than the area of the opening on the stove. If the area of the flue is larger than the area of the opening on the stove, it should never be more than three (3) times larger. Exception: If you reline the flue and direct connect this unit, a six inch (6”) flue liner is acceptable. SECTION II: FLOOR PROTECTION Hearth Extension The firebox on your insert will extend out ten inches (10”) from the face of the fireplace, so you will need at least sixteen inches (16”) in front of the door. If you do not have this, it will require you to place an approved floor protector in front of the stove (such as a hearth extender shield). These boards can be purchased from your local dealer or from our factory. SECTION III: INSTALLATION INTO A MASONRY FIREPLACE A. Preparation 1. Measure your hearth to ensure it is large enough to accept the unit. Your hearth should be at least thirty-six inches (36”) wide and fourteen inches (14”) from the face of the fireplace to the edge of the hearth. 2. Inspect your hearth to be sure it is constructed of a noncombustible material such as brick or stone. Do not install this stove on a hearth that is constructed of wood framework that is covered by brick or stone and do not install this unit in a zero (0) clearance fireplace. The manufacturer will not be held responsible for an accident resulting from this stove being installed on a hearth constructed of a combustible material. 3. Inspect your fireplace to ensure it is in proper working order and free of any obstructions. 4. Prior to installation, remove the existing damper or wire it to fasten it open. 5. Place the insert on the hearth and slide about one-third (1/3) of it into the opening. B. There Are Two Methods of Venting Your Insert 1. Direct Connect When this unit is direct connected it will require eight inch (8”) diameter 24 gauge pipe from the stove through the damper opening. This will make it necessary to block off the open area on both sides of the pipe that passes through the damper opening, which can be done with sheet metal or by packing flame retardant fiberglass insulation in the open areas. You must be sure the draft from the chimney is being pulled through the stove, and not around the connector pipe. If you do direct connect, we highly recommend you have it done by a professional. You should contact your local authorities, as some areas require this unit to be installed by the direct connect method. 2. Direct Dump The cover plate (STB-J) and its gasket (AC-PGK) are supplied with the unit and ar...

Este manual também é adequado para os modelos :
Placa - 50-SHW20 (64.12 kb)
Placa - 50-TRW20 (64.12 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias