Assessments - 3, GPA: 3
(
)
)
|
Facilidade de uso
Finishing the ARS Installation 1. Re-install the ARS channel that was removed in Step 3 on page one and secure with 2 bolts previously removed. Set the grate into the ARS channel Replace the 2 front cut bricks. Figure 22.2. 2. Install the ash drawer. 3. Check to make sure baffle boards and ceramic blanket are in their proper locations. (see page 29). NOTE: If installing a floor installation of an outside air kit on a Step Top model with a pedestal assembly you must attach the enclosed cover plate to the back of the stove. Other wise you may discard this piece. Figure 22.3. September 1, 2008 7037-135E Page 23 4300 Wood Stove Series (ACC) R B. Leg Kit and Ash Removal Installation (ARS) for Step Top Uni-Body Do NOT tilt the unit on the cast iron legs. • Tilting could lead to property damage. • Lift the unit upright and place it into position on the floor protector. CAUTION Lay stove flat on its back on protective padding or pallet Insert 2 bottom screws loosely Ash Drawer Leg Brackets NOTE: The Ash Removal System, must be installed first before installing the legs. Figure 23.1 Figure 23.2 Leg Mounting Brackets are packaged inside firebox. Leveling Legs at opposite corners Installing Leg Kit 1. Remove leg mounting brackets packaged inside firebox. 2. Attach the 2 bottom screws of the mounting brackets to the bottom of the stove with 1/4”-20 Phillips head screws. These screws are located in the component pack . Leave the bottom 2 screws loose so you can slide the ash pan assembly bottom slots over the screw heads. This allows the weight of the ash pan to rest on the screws while you are attaching the top 2 screws. Once the ash pan is attached, tighten all screws. Figure 23.2. 3. Loosely assemble bolts into the corner of the mounting brackets for leg attachment. Figure 23.1. 4. Slide legs onto mounting brackets and tighten. Make sure the legs are up against the bracket. There are leveling bolts in 2 legs. These leveling legs should be in opposite corners. Figure 23.1. 5. Carefully stand stove up and place in desired location. Do NOT tilt up on the cast iron legs, it could damage the legs. 6. Use leveling bolts on legs to stabilize and level stove. Finishing the ARS Installation 1. Follow steps 1 through 3 on page 22. See also Figure 22.2. 4300 Wood Stove Series (ACC) R C. Door Handle Assembly 1. Install washer on door handle shaft. 2. Slide door handle through door. . Install second washer(s) as shown. 4. Install key in groove. 5. Align groove in latch cam with key; slide latch cam over shaft 6. Install locknut but do not overtighten, it must move smoothly. 7. Install spring handle turning in a counter-clockwise motion to desired location on door handle rod. CAUTION • Do NOT overtighten lock nut. • Door handle needs to move smoothly. D. Adjusting The Blower Speed Control The blower speed control for this unit is adjusted at the factory, and normally does not require further adjustment. NOTE: When the speed control is turned clockwise, it will click on to high speed. Continue to turn the speed control clockwise to decrease the speed. At full clockwise, the blower should blow gently, but should not stop. 1. With the appliance plugged in, turn the speed control knob to slow (full clockwise). 2. With a small screwdriver, adjust the blower speed by turning the adjustment mechanism through the hole on the side of the speed control. . Adjust the speed so the blower runs slowly, but does not stop. Turn clockwise to slow the blower and counterclockwise to increase the speed. Locknut Door Cross Section (example) Latch Cam Spacing Washers Square Key Door Handle Spring Handle Figure 24.1 Page 24 7037-135E September 1, 2008 R 4300 Wood Stove Series (ACC) 8Operating Instructions A. Over-Firing Your Appliance WARNING Do not over-fire. Over-firing may ignite creosote or will damage the stove and chimney. To prevent over-firing your stove, DO NOT: • Use flammable liquids • Overload with wood • Burn trash or large amounts of scrap lumber • Permit too much air to the fire Fire Risk 1. Symptoms of Over-Firing Symptoms of over-firing may include one or more of the following: • Chimney connector or appliance glowing • Roaring, rumbling noises • Loud cracking or banging sounds • Metal warping • Chimney fire 2. What To Do if Your Stove is Over-Firing • Immediately close the door and air controls to reduce air supply to the fire. • If you suspect a chimney fire, call the fire department and evacuate your house. • Contact your local chimney professional and have your stove and stove pipe inspected for any damage. • Do not use your stove until the chimney professional informs you it is safe to do so. Hearth & Home Technologies WILL NOT warranty stoves that exhibit evidence of over-firing. Evidence of over-firing includes, but is not limited to: • Warped air tube • Deteriorated refractory brick retainers • Deteriorated baffle and other interior components B. Wood Selection & Storage Burn only dry seasoned wood. Store wood under cover, out o...
Este manual também é adequado para os modelos :Placa - Quadra-Fire 43M-ACC-MBK (2.97 mb)