Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
Area Cleaning agents Self-cleaning surfaces (rough surfaces) Note the instructions in the section: Catalytic cooking compartment panel Gas burner Never clean the gas burners in the cooking compartment yourself. Door panels Glass cleaner: Clean with a soft cloth. Do not use a glass scraper. Glass cover for the oven light Hot soapy water: Clean with a dish cloth. Seal Do not remove. Hot soapy water: Clean with a dish cloth. Do not scour. Rails Hot soapy water: Soak and clean with a dish cloth or brush. Accessories Hot soapy water: Soak and clean with a dish cloth or brush. Catalytic cooking compartment panels The catalytic cooking compartment panels are coated with self- cleaning enamel. The surfaces clean themselves while the oven is in operation. Larger splashes will only be removed after the oven has been used several times. Self-cleaning surfaces The side walls are covered with catalytic panelling. Never clean these surfaces with oven cleaner. Slight discolouration of the enamel does not affect automatic self-cleaning. Removing and fitting the appliance door You can remove the appliance door to clean it more thoroughly. Removing the appliance door : Risk of injury! Whenever the hinges are not locked, they snap shut with great force. When removing the oven door, ensure that the locking pins are fully inserted into the holes in the hinges. 1. Open the oven door fully. 2. Lock both hinges on the left and right using a locking pin (a). Note: The locking pins must be fully inserted into the holes in the hinges. 3. Grip the oven door on either side with both hands and close the oven door by approx. 30° (b). 4. Raise the oven door slightly and pull it out. Note: Do not fully close the oven door. The hinges may become bent and the enamel may be damaged. Fitting the appliance door 1. Grip the oven door on either side with both hands. 2. Slide the hinges into the slots in the oven (a). Note: The notch below the hinges must engage into the frame of the oven (b). 3. Lower the door downwards. 4. Remove the locking pins. : Risk of injury! If the oven door falls out accidentally or a hinge snaps shut, do not reach into the hinge. Call after-sales service. Removing and inserting the hook-in racks You can remove the hook-in racks for easier cleaning. Removing the hook-in racks The hook-in racks in each case are fixed to the side walls of the cooking compartment at three points. 1. Grip the hook-in rack on the front and pull it to the middle of the cooking compartment. The front hook of the rack will release from the hole. 2. Fold out the hook-in rack further and pull it from the rear holes of the side panel. 3. Hold the catalytic cooking compartment panel in place. 4. Pull the hook-in rack out of the holes. Inserting the hook-in rack 1. Hold the catalytic cooking compartment panel in place. 2. Insert the hooks of the hook-in rack into the rear holes in the side panel. 3. Press the front hook of the hook-in rack into the hole. Troubleshooting Malfunctions often have simple explanations. Refer to the table before calling the after-sales service, as you may be able to remedy the fault yourself. : Risk of injury! Incorrect repairs are dangerous. Repairs may only be carried out, and damaged power and gas lines replaced, by an after- sales engineer trained by us. If the appliance is faulty, unplug the mains plug or switch off the fuse in the fuse box. Shut off the gas supply. Contact the after-sales service. Malfunction Possible cause Solution The appliance Power cut Check whether other does not work kitchen appliances are working Faulty circuit Check in the fuse box to breaker make sure that the circuit- breaker for the appliance is OK The oven light-Oven light is Replace the oven light. ing has failed. faulty (See section "Replacing oven light") The flame Normal build-up The burner must be profes( oven) does not of dirt sionally cleaned. burn through all outlet openings. The door panel Normal occur-Not possible; this has no steams up rence; caused effect on oven performance. when the oven by the differ- heats up. ence in temperature Replacing the oven light bulb If the oven light bulb fails, it must be replaced. Replacement heat-resistant bulbs can be obtained from the after-sales service or from specialist retailers. Please specify the E number and FD number of your appliance. Do not use any other type of bulb. : Risk of electric shock! When replacing the cooking compartment bulb, the bulb socket contacts are live. Before replacing the bulb, unplug the appliance from the mains or switch off the circuit breaker in the fuse box. 1. Allow the cooking compartment to cool down. 2. Open the appliance door. 3. Place a tea towel in the cooking compartment to prevent damage. 4. Remove the glass cover for the oven light bulb using a suitable tool (e.g. screwdriver). 5. Unscrew and remove the oven light. 6. Replace the oven light bulb with a bulb of the same type Voltage: 240 V; Power: 25 W; Thread: E14; Temperature resistance: 300...
Este manual também é adequado para os modelos :Placa - HGL10E150/02 (3.04 mb)