Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
The safety ignition is activated. If the gas flame goes out, the gas supply is automatically interrupted by the safety ignition system. 6. Look through the inspection port to make sure that the flame is lit. If it is not, repeat the process from step 3. 7. Close the oven door slowly. 8. Preheat the empty oven for approximately 15 minutes before baking. 9. When the dish has finished cooking, turn off the switch for the lower gas burner. You can change the temperature at any time. : Caution:! The ignition device should not be actuated for more than 15 seconds. If the burner does not light within 15 seconds, wait for at least one minute. Then repeat the ignition process. Setting procedure for the gas grill in the oven 1. Open the top cover. The top cover must remain open for as long as the oven is in operation. 2. Open the main gas supply to the appliance. Connect the plug in the socket. 3. Insert the protective plate into the groove under the control panel. The protective plate is inserted with the longer edge at the front and the curvature pointing downwards. Secure the protective plate in the groove underneath the control panel using the retainers. Make sure that the protective plate is engaged in the retainers. If the protective plate cannot be pulled out, it is correctly engaged. You can now use the protective plate safely. Otherwise, insert the protective plate into a groove at a slightly higher angle and make sure that it engages in the retainers. 4. Close the oven door so that it touches the protective plate. 5. Press the function selector and turn it clockwise to the ( grill setting. 6. Keeping the function selector pressed, push the 8 ignition button. 7. The gas escaping from the gas grill is ignited using the ignition button. To activate the safety pilot, press and hold the function selector for 10 seconds. The safety pilot is activated. If the gas flame goes out, the gas supply is automatically interrupted by the safety pilot. 8. Check that the flame is lit. If it is not, repeat the process from step 5. 9. When the dish has finished cooking, switch the function selector off. Once the oven has cooled down, remove the protective plate again. : Caution! The ignition device should not be actuated for more than 15 seconds. If the burner does not light within 15 seconds, wait for at least one minute. Then repeat the ignition process. Grilling with the rotary spit The rotary spit is particularly good for cooking large roasts, such as rolled roasting joints or poultry. The meat becomes crispy and brown. 3. Insert the baking tray at level 1. There is an opening in the back wall of the oven. The rotary spit hooks into this (Fig. C). 4. Remove the handle and close the oven door (Fig. D). Preparing roasts To ensure that the roast is well-browned and cooked evenly, observe the following points: Skewering and securing the joint to the spit Position the joint as close as possible to the centre of the rotary spit. Use the clamps to secure it at both ends. The rear clamp must be a minimum of 7 cm from the end of the spit. You can also truss the joint with string. With poultry, bind the ends of the wings underneath the back and the thighs against the body. This prevents them from overbrowning. Pierce the skin on the underside of the wings to allow the fat to escape. In the section Tables and tips, you will find a variety of setting values for grilling with the rotary spit. Inserting the rotary spit 1. Place the rotary spit holder on the baking tray (Fig. A). 2. Place the rotary spit in the holder (Fig. B). .... .... How to set the rotary spit and grill Follow the instructions below to switch on the rotary spit. If you want to grill with the rotary spit, you must first insert it in the oven and then follow the instructions below. 1. Open the top cover. The top cover must remain open for as long as the oven is in operation. 2. Open the main gas supply to the appliance. Connect the plug to the socket. 3. Insert the protective plate into the groove under the control panel. The protective plate is inserted with the longer edge at the front and with the elbow pointing downwards. Secure the protective plate in the groove underneath the control panel using the retainers. Make sure that the protective plate is engaged in the retainers. If the protective plate cannot be pulled out, it is correctly engaged. You can now use the protective plate safely. Otherwise, insert the protective plate into a groove at a slightly higher angle and make sure that it engages in the retainers. 4. Close the oven door so that it touches the protective plate. 5. Press the function selector and turn it clockwise to the ( grill setting. 6. Keeping the function selector pressed, push the 8 ignition button. 7. The gas escaping from the gas grill is ignited using the ignition button. To activate the safety ignition, press and hold the function selector for 10 seconds. The safety ignition is activated. If the gas flame goes out, the gas supply is autom...
Este manual também é adequado para os modelos :Placa - HGG223326Z/02 (2.44 mb)
Placa - HGG223326Z/03 (2.44 mb)
Placa - HGG223326Z/04 (2.44 mb)