Log:
Assessments - 2, GPA: 3.5 ( )

Instruções de Operação Vermont Castings, Modelo LHEC20

Fabricante : Vermont Castings
Arquivo Tamanho: 264.88 kb
Arquivo Nome : 3d0e52be-93b4-f204-7914-a300e5d974cc.pdf
Língua de Ensino: en
Ir para baixar



Facilidade de uso


Report any missing or damaged parts to your dealer immediately. Install trim kit after all other fireplace installation work has been completed, thoroughly checked and tested for proper operation, leaks and installation requirements. Tools required: Tape measure Trim kit parts Part # Column Right Assembly 30002073 (1) Column, right 30001978 (1) Boot, right 30001982 (1) Slider Clip, right 30002050 (1) Bracket, On/Off Switch 10005035 (2) 1/4-20 Round Head Screw 1200894 (2) 1/4-20 Wing Screw 1201621 (3) 1/4 Flat Washer 1202474 Column Left Assembly 30002074 (1) Column, left 30001979 (1) Boot, left 30001983 (1) Slider Clip, left 30002049 (1) 1/4-20 Round Head Screw 1200894 (2) 1/4-20 Wing Screw 1201621 (3) 1/4 Flat Washer 1202474 Key 30001981 Upper Mounting Bracket 30002053 Upper Mounting Bracket R 30002054 Hardware Bag: 30001988 (5) 1/4-20 Wing Screw 1201621 (5) 1/4 Flat Washer 1202474 Instruction Sheet 30001987 Assembly Determine which model fireplace insert you have. This will be important when adjusting the height and width of the surround. 1. Place the key (30001981) on your work surface with the threaded holes facing up. 2. Place the column right assembly (30002073) onto the key. (Fig. 1) 3. Place the column left assembly (30002074) onto the key. (Fig. 2) 4. Install the upper mountingbracket. Use the upper mounting bracket marked R (30002054) for the LHER20. Use the unmarkedupper mounting bracket (30002053) for LHEC30and LHEC20. (Fig. 3) 30001987 8/08 Rev. 4 5. Fasten the upper mounting bracket to the key with a 1/4-20 wing screw and 1/4 flat washer finger tight. (Fig. 3) 6. Fasten the upper mounting bracket to both column assemblies using (2) 1/4-20 wing screws and (2) 1/4 flat washers per side finger tight. The distance between the insides of the columns should measure: LHEC30 = 293/i6” (741mm) LHEC20 & LHER20 = 25%” (651mm) 7. Adjust the column/boot length (measure from the bottom side of the key to the bottom of the boot). LHEC30 = 221/4” (565mm) LHEC20 = 181/4” (464mm) LHER20 = 17%” (448mm) 8. Lift the surround up and parallel to the fireplace front. Press the Fan ON/OFF switch into the switch bracket. It will snap into place. (Refer to Homeowner’s manual for additional switch installation instructions) Move the surround towards the fireplace about an inch above the hearth. As you lower the surround onto the fireplace, the side clips and top bracket will engage mating clips. If height and width adjustments are required, lift the surround up and out. Make the adjustments. Regardless if adjustments were made or not, tighten all wing screws fasteners and return the surround to the fireplace. _MHSC_ 149 Cleveland Drive • Paris, Kentucky 40361 www.mhsc.com...

Este manual também é adequado para os modelos :
Placa - LHER20 (264.88 kb)

Escreva a sua própria avaliação do dispositivo



Mensagem
Seu nome :
Introduza os dois dígitos :
capcha





categorias