Assessments - 3, GPA: 5
(
)
)
|
Facilidade de uso
1 .................. 1. Remote sensor reception indicator 2. Outdoor temperature 2 3. Indoor temperature 4. Ice alert LED indicator 3 BACK VIEW – FIG. 2 1. °C / °F : Select temperature unit 2. RESET: Reset unit to default settings 4 REMOTE SENSOR – FIG. 3 1. LED status indicator 2. Wall mount hole 3. Battery compartment 4. RESET hole 5. CHANNEL switch GETTING STARTED INSERT BATTERIES 1. Remove the battery compartment. 2. Insert the batteries, matching the polarities (see FIG 2). 3. Press RESET after each battery change. LOCATION Indoor temperature area Outdoor temperature area MEANING Main unit batteries low Sensor batteries low REMOTE SENSOR To set up the sensor: 1. Open the battery compartment (see FIG 3). FIG. 3 2. Select channel 1 then press RESET. 3. Close the battery door. 4. Place the sensor within 30 m (98 ft) of the main unit using the table stand or wall mount. TIP Ideal placements for the sensor would be in any location on the exterior of the home at a height of not more than 5 ft and which can shield it from direct sunlight or wet conditions for an accurate reading (see FIG. 4). 4 5 NOTE Use alkaline batteries for longer usage and consumer grade lithium batteries in temperatures below freezing. SENSOR DATA TRANSMISSION To search for a sensor: Reset the unit. The sensor reception icon in the remote sensor area shows the status: ICON DESCRIPTION Main unit is searching for sensor(s). A channel has been found. The sensor cannot be found. OUTOUTOUTOUTOUTOUTOUT TIP The transmission range may vary depending on many factors. You may need to experiment with various locations to get the best results. ICE WARNING If the channel 1 sensor falls between 3°C to -2 °C (37°F to 28°F), LED indicator will flash, and will stop flashing once the temperature is out of this range. • Do not cover the ventilation holes with any items such as newspapers, curtains etc. • Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth. • Do not clean the unit with abrasive or corrosive materials. • Do not tamper with the unit’s internal components. This invalidates the warranty. • Only use fresh batteries. Do not mix new and old batteries. • Images shown in this manual may differ from the actual display. • When disposing of this product, ensure it is collected separately for special treatment. • Placement of this product on certain types of wood may result in damage to its finish for which Oregon Scientific will not be responsible. Consult the furniture manufacturer’s care instructions for information. • The contents of this manual may not be reproduced without the permission of the manufacturer. • Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary. • Please note that some units are equipped with a battery safety strip. Remove the strip from the battery compartment before first use. NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice. SPECIFICATIONS TYPE DESCRIPTION MAIN UNIT L x W x H 241 g (8.5 oz) without battery 66 x 27.5 x 87.5 mm (2.59 x 1.08 x 3.44 in) Weight Temperature range -5°C to 50°C (23°F to 122°F) Resolution 0.1°C (0.2°F) Signal frequency 433 MHz Power 2 x UM-4 (AAA) 1.5 V batteries REMOTE UNIT (THN132N) L x W x H 96 x 50 x 22 mm (3.78 x 1.97 x 0.87 in) Weight 62 g (2.22 ounces) Transmission range 30 m (98 ft) unobstructed Temperature range -20°C to 60°C (-4°F to 140°F) Power 1 x UM-3 (AA) 1.5 V batteries ABOUT OREGON SCIENTIFIC Visit our website () to learn more about Oregon Scientific products. If you’re in the US and would like to contact our Customer Care department directly, please visit: www2.oregonscientific.com/service/support www2.oregonscientific.com/service/support OR Call 1-800-853-8883. For international inquiries, please visit: www2.oregonscientific.com/about/international www2.oregonscientific.com/about/international EU-DECLARATION OF CONFORMITY Hereby, Oregon Scientific, declares that this Wireless Indoor and Outdoor Thermometer with LED Ice Alert (Model: EMR201) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service. COUNTRIES RTTE APPROVED COMPLIED All EU countries, Switzerland and Norway CH N CH FIG. 2 RESET C/ F 21 2 3 FIG. 4 RESET FCC STATEMENT This device complies with Part 15 of the FCC Rules. Press RESET to return to the default settings. PRECAUTIONS Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including• Do not subject the unit to excessive force, shock, dust, interference that may cause undesired operation. temperature or humidity. WARNING Changes or modificat...