Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit is in a safe condition. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. Never use your hands to locate a hydraulic leak on attachments. Use a small piece of cardboard or wood. Hydraulic fluid escaping under pressure can penetrate the skin. Openings in the skin and minor cuts are susceptible to infection from hydraulic fluid. If injured by escaping hydraulic fluid, see a doctor at once. Gangrene and death can result. Without immediate medical treatment, serious infection and reactions can occur. 11 SAFETY INSTRUCTIONS (continued) MAINTENANCE SAFETY (continued) After servicing, be sure all tools, parts and service equipment are removed. Check to ensure all safety signs are installed and in good condition. (See safety sign section for location drawing.) Do not allow grease or oil to build up on any deck or platform. Never replace hex bolts with less than grade five bolts unless otherwise specified, i.e. shear bolts. Refer to bolt torque chart for head identification marking. Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts must be used to restore your equipment to original specifications.The manufacturer will not claim responsibility for use of unapproved parts and/or accessories and other damages as a result of their use. If equipment has been altered in any way from original design, the manufacturer does not accept any liability for injury or warranty. A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance on this equipment. STORAGE SAFETY Following operation or when unhooking, stop the tractor, set the brakes, disengage the PTO, shut off the engine and remove the ignition keys. Never unhitch without using the tongue jack. The tongue is very heavy. Attempting to lift the tongue without using the tongue jack could cause strains. Allowing the tongue to fall suddenly and unexpectedly could result in crushing injury. Use the tongue jack for lifting the implement only. Overloading the jack can cause failure with possible serious bodily injury or even death. Store the unit in an area away from human activity. Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock injury could result. Do not permit children to play on or around the stored unit. Make sure all parked machines are on a hard, level surface and engage all safety devices. If blocking is used, make sure it is solid and secure before leaving area. 12 SAFETY SIGNS Always insert spears in bale – never under bale. Failure to do this can allow bale roll back when loader is raised, causing serious injury or death. 101127 (Models GLB-3000, GLB-330, GLB-340) WARNING BE CAREFUL! Use a clean, damp cloth to clean safety decals. Avoid spraying to close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off. REMEMBER: If Safety Signs have been damaged, removed, become illegible or parts replaced without Signs, new Safety Signs must be applied. New Safety Signs are available from your authorized distributor or factory. 13 INSTRUCTIONS TRACTOR AND LOADER REQUIREMENTS AND PREPARATION —————————————————— The Bale Spear Attachments are designed to fit Loaders equipped with a tool carrier that accepts Global or Euro Hook Style attachments. The required size of the tractor and front loader will be determined by the size and weight of the bales to be handled. Remember, high moisture hay (silage) bales are very heavy in relation to similar size dry hay bales. Always use a power unit/loader large enough to safely handle your bales. Always be sure your power unit is properly counterbalanced for a safe operation. It is a good practice to use a loader with an equal or greater SAE operating load capacity. The maximum recommended weight of large round bales that can be handled by the various single/two spear models and weights of rectangular bales that can be handled by three spear units are as follows: Model Spear Type Bale Weight GLB-2200 Forged Up to 2200 lbs. GLB-3000 Forged (2) Up to 3000 lbs. GLB-330 Forged (3) Up to 3000 lbs. GLB-340 Forged (3) Up to 4000 lbs. WARNING! For multiple spear Models GLB-3000, GLB-330, GLB-340, always insert spears into the bale – NEVER under the bale. Failure to insert spears into bale can allow bale to roll back when loader is raised, causing serious injury or death. Always use a tractor and front loader large enough to safely handle your bales. Check your tractor and front loader to make sure they are in good working condition. Check all loader mounting bolts to make sure they are tight. Check the tractor’s hydraulic system. Be sure the hydraulic oil and filter have been serviced accor...

Este manual também é adequado para os modelos :
Carregadores - GLB-3000 (601.21 kb)
Carregadores - GLB-330 (601.21 kb)
Carregadores - GLB-340 (601.21 kb)