Assessments - 2, GPA: 4
(
)
)
|
Facilidade de uso
o Do not open the door when the display shows "High temperature", as very hot steam inside the appliance can cause burns. o Keep children away from the appliance when the door is opened. o Do not use if the safety locking system is not functioning, which means that the appliance could be switched on even if the door is not closed. • Avoid touching the heating element in the base of the appliance (below the filter) immediately after use, as this can be very hot. KEY TO MAIN COMPONENTS OF THE APPLIANCE 1. Washing rack 2. Salt container 3. Door release button 4. Display 5. Control buttons 6. On/Off button 7. Measuring spoon 8. Cutlery basket 9. Filler cap 10. Detergent compartment a. Water intake b. Drainage nozzle c. Drainage hose (disconnected) d. Hose clip e. Power cord f. Height-adjustable legs g. Surface-active agent container cover (removed) h. Surface-active agent container I. Displays selected wash program II. Displays time III. On/off indicator IV. Salt indicator V. Pause/start button VI. Program selector button VII. Displays program cycle PREPARING THE APPLIANCE Each individual appliance is checked at the factory, but for safety’s sake, after unpacking it, you should check carefully that it has not been damaged during transport. • Check whether there is any visible damage (e.g. in the form of dents or similar), if the door closes properly, and if the hinges are in order. • If the appliance appears to have been damaged, contact the shop where you bought it, and do not use it until it has been checked by an authorised specialist. • Before use, check that you have removed all packaging inside and out. Positioning the appliance • The appliance must stand on a flat surface capable of bearing its weight (17.3 kg). • The appliance must be level – adjust the four height-adjustable legs (f) if necessary. • For domestic use only. There must be a clearance of at least 10 cm at the rear, 5 cm at the sides and 48 cm above to ensure sufficient ventilation. Connection • The microwave oven must be connected to a 230-volt AC current, 50 Hz. • Always use new hoses when installing the appliance. Old hoses should not be reused for new installations. • Screw the hose to the water supply at the water intake (a). o The water intake on the appliance ends in a ." female plug – check that the correct hose is used. o Do not tighten the connection too much, as this can damage the thread. o There should be a stopcock connected to the hose, so it is easy to disconnect the water supply to the appliance. o Water can be supplied from a normal tap, but it is recommended that the appliance be connected to a permanent water supply, if possible. You must ensure that the correct spacers or adapters are used to connect the appliance in a safe and secure manner. o The appliance uses water with a temperature of 55 .C, and it is therefore normally connected to the hot water supply. . If the hot water supply temperature cannot be kept below 65 .C, the appliance must be connected to the cold water supply, as it may be damaged by water that is too hot. o Water pressure must be between 0.03 MPa and 1.0 MPa to ensure good results. o The appliance is equipped with a water level gauge, which ensures that the appliance stops automatically if there is a drop in water pressure. • Attach the drainage hose (c) to the drainage nozzle (b) using the hose clip (d). Tighten the hose clip until the hose is secure. o NOTE: TAKE CARE WHEN TIGHTENING THE HOSE CLIP, AS IT HAS SHARP EDGES. o The drainage hose is fed upwards like an upturned U over the accompanying plastic U-bend (not shown) before being fed downwards into the drain. This prevents drainage water flowing back into the appliance. For increased protection, a reflux valve (not included) can be used. o The drainage hose should be fed down into a drainage pipe, which must be no higher than max. 15 cm above the base of the appliance. The drainage pipe diameter should be at least 30 mm in order to ensure that air can escape around the drainage hose. • Switch on the power. UK NOTE: AS SOON AS THE WATER SUPPLY IS TURNED ON, THERE IS PRESSURISED WATER IN THE HOSE AND APPLIANCE, EVEN IF THE WATER SUPPLY IS SUBSEQUENTLY TURNED OFF AGAIN! Fitting the filter, rack and cutlery basket • Fit the steel filter (not shown) in the base of the appliance. o The filter is to be fitted with the handle outwards. o Check that the filter is correctly fitted and that the washer arm can move freely and can turn a complete circle. • The washing rack (1) is equipped with wheels, so that it slides easily in and out. • Position the cutlery basket (8) on the rack. The cutlery basket can be removed from the washing rack if it is not required, e.g. when washing dishes, bowls and other large objects. Filling with salt and surface-active agent Water hardness varies from place to place and from waterworks to waterworks. Hard water can leave white deposits on dishes and requires more detergent. This appliance is therefore equipped with a s...