Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
To help you get water of the proper temperature, your dishwasher automatically heats the water in the wash cycle. For good washing and drying, the entering water must be at least 120°F. To prevent dish damage, inlet water should not exceed 150°F. How to Test Water Temperature Higher water temperature is needed to dissolve grease and activate powder detergents. Check your water temperature with a candy or meat thermometer. Turn on the hot water faucet nearest the dishwasher. Put the thermometer in a glass and let the water run continuously into the glass until the temperature stops rising. If the water temperature is below 120°F, adjust your water heater. Helpful Hints If outside temperatures are unusually low, or if your water travels a long distance from water heater to dishwasher, you may need to set your water heater’s thermostat up. If you have not used hot water for some time, the water in the pipes will be cold. Turn on the hot water faucet at the sink and allow it to run until the water is hot. Then start the dishwasher. If you’ve recently done laundry or run hot water for showers, give your water heater time to recover before operating the dishwasher. To improve washability if the water is less than 120°F and you cannot adjust your water heater: Select a longer cycle and fill both detergent cups at least half full with detergent. Operating Energy-Saving Hot Water Cycles POTS & PANS NORMAL WASH RINSE & DRY CHINA & CRYSTAL RINSE & HOLD 5 Energy-Saving Tips • Operate dishwasher only when it’s full. Let the dishes accumulate in dishwasher. When you put in only a partial load, use the RINSE & HOLD cycle to rinse off heavy soils. Be sure to latch the door when waiting for a full load. This helps keep soils moist, easier to remove. • If you don’t need your dishes right away, open your dishwasher door and they will dry naturally over a longer period such as overnight. • Always select the cycle that uses the least amount of water that will remove the soil from the load. Water Use Gallons (approx.) 7.3 5.7 4 4.4 1.8 Wash Cycle Time Minutes (approx.) 90–95 80–87 50 53 8 Pre Wash Pre Wash Wash Rinse Wash Rinse Rinse Wash Rinse Cycle Sequence Rinse Rinse Rinse Rinse Rinse Dry Dry Dry Dry Rinse Good Dishwashing Starts with HOT Water To get dishes clean and dry, you need hot water. To help you get water of the proper temperature, your dishwasher automatically heats the water in the wash cycle. For good washing and drying, the entering water must be at least 120°F. To prevent dish damage, inlet water should not exceed 150°F. How to Test Water Temperature Higher water temperature is needed to dissolve grease and activate powder detergents. Check your water temperature with a candy or meat thermometer. Turn on the hot water faucet nearest the dishwasher. Put the thermometer in a glass and let the water run continuously into the glass until the temperature stops rising. If the water temperature is below 120°F, adjust your water heater. Helpful Hints If outside temperatures are unusually low, or if your water travels a long distance from water heater to dishwasher, you may need to set your water heater’s thermostat up. If you have not used hot water for some time, the water in the pipes will be cold. Turn on the hot water faucet at the sink and allow it to run until the water is hot. Then start the dishwasher. If you’ve recently done laundry or run hot water for showers, give your water heater time to recover before operating the dishwasher. To improve washability if the water is less than 120°F and you cannot adjust your water heater: Select a longer cycle and fill both detergent cups at least half full with detergent. Operating Energy-Saving Hot Water Cycles POTS & PANS NORMAL WASH RINSE & DRY CHINA & CRYSTAL RINSE & HOLD 5 How to Use a Rinse Agent It is recommended that a liquid rinse agent be used at all times with your dishwasher. Do not use powder or solid rinse agents. Your rinse agent has a dual purpose with your dishwasher. It makes water flow off dishes quicker than usual. This lessens water spotting and makes drying faster, too. The rinse agent also serves to rinse the tub and the inner door of the dishwasher. Your tub and inner door will begin to take on a dull, unpolished look if rinse agent is not used. For best dishwashing performance, use of a rinse agent such as JET-DRY brand is recommended. Your dishwasher is equipped with a reservoir for storing and dispensing liquid rinse agent. To fill the rinse agent reservoir: • Remove the reservoir cap. • Pour the rinse agent into the reservoir until the clear level indicator turns completely dark. The reservoir is full when the level indicator is dark. • Replace rinse agent reservoir cap. A full reservoir will provide enough rinse agent for approximately 30 washes. Rinse Agent Indicator On your control panel is the rinse agent indicator. This indicator light shows you the level of the FILL RINSE AID rinse agent that is in the rinse agent reservoir. When the ind...