Assessments - 2, GPA: 3
(
)
)
|
Facilidade de uso
Using too much detergent in soft water can cause a permanent film called etching. Your local water company, water softener company or county extension agent can tell you the water hardness in your area. Cover Main Wash Cup Cover Latch Pre Wash Cup Note: If the cover is closed on the Main Wash Cup, open by pressing the cover latch. Detergent Usage Guide Cycle Soft Water (0-3 grains) Medium Hard Water (4-8 grains) Hard Water (9-12 grains) Very Hard Water* (over 12 grains) Pots & Pans or Normal Wash 2 teaspoons (each cup– 1/4 full) 5 teaspoons (each cup–fill to line above "Regular") 8 teaspoons (each cup– completely full) Each Cup– Completely Full (water softener recommended) Eco Wash or Upper Rack 2 teaspoons (each cup– 1/4 full) 5 teaspoons (each cup–fill to line above "Regular") 8 teaspoons (each cup– completely full) Each Cup– Completely Full (water softener recommended) Rinse Only No Detergent No Detergent No Detergent No Detergent (water softener recommended) *Note: For very hard water, detergent alone may not be enough. A water softener is recommended to improve water quality and dishwashing performance. Try adding more detergent at the beginning of the main wash portion of the cycle. As a rule, use 1 teaspoon for each grain above 12. Unlatch the door, open slowly and add detergent to the bottom of the tub. Close the door to latch and the dishwasher will continue through the cycle. 10 Dishwasher Dispenser& Detergents (continued) Rinse Aid Rinse aid greatly improves drying and reduces water spots and filming. Water "sheets" off dishes rather than forming water droplets that cling and leave spots. A dispenser, located next to the detergent cup, automatically releases a measured amount of rinse aid during the last rinse. If spotting and poor drying are problems, increase the amount of rinse aid dispensed by rotating the dial to a higher number. The dial is located under the dispenser cap. The indicator will be dark when full and will show clear when it is time to refill. To add liquid rinse aid, turn dispenser cap 1/4 turn counterclockwise and lift out. Pour in rinse aid until liquid touches the indicated fill level. Replace cap. Do not overfill since this can cause oversudsing. Wipe up any spills with a damp cloth. The dispenser holds enough for 35 to 140 washes, depending on setting. Dispenser Opening Indicator Adjustable settingDispenser Cap Less More Factors Affecting Performance Water Pressure The hot water line to dishwasher must provide water pressure between 20 and 120 psi. Low water pressure may occur when laundry or showers are in operation. Wait until water use is reduced before starting dishwasher. Water Temperature Hot water is needed for best dishwashing and drying results. Water entering dishwasher should be at least 120°F (49°C) to give satisfactory results. To check water temperature entering dishwasher: • Turn on hot water faucet nearest dishwasher for several minutes to clear cool water from pipes. • Hold a candy or meat thermometer in stream of water to check the temperature. • If temperature is below 120°F (49°C), have a qualified person raise the hot water heater thermostat setting. Important: Before starting a cycle, run hot water to clear cool water from pipe. The HEAT DRY option in combination with rinse aid will enhance drying performance. The energy required to use the HEAT DRY option costs pennies per cycle. You may choose not to select the HEAT DRY option; however you will have items in your dish load that will not be completely dry at the end of the cycle. 11 Care and Cleaning Allow heating element to coolbefore cleaning the interior. Failure to do so can result in burns. Burn Hazard Outside—Occasionally wipe with a mild nonabrasive detergent and water. Rinse and dry. Models with Stainless Steel Door— Clean outer door with warm soapy water and a dishcloth or sponge. Rinse with clean water and a dry cloth. Do not use harsh cleaners. Inside—The inside of the dishwasher is self- cleaning with normal use. If needed, clean around the tub gasket area with a damp cloth. The filter is self- cleaning. A glass trap located in the center of the filter is designed to collect pieces of broken glass, straws, bones and pits. To remove items in glass trap, grasp handle, lift out, empty and replace. Note: Hard water may cause lime deposit buildup on the interior of the dishwasher. For cleaning instructions see “Removing Spots and Film” section. Overfill Protector—keeps dishwasher from overfilling and is located in the left front corner of the tub. • Clean occasionally with household cleaner containing vinegar or bleach to dissolve any buildup. • Overfill Protector should move up and down freely about one inch. If it does not move, lift and clean underneath. Care of Drain Air Gap If a drain air gap was installed for your built-in dishwasher, check to make sure it is clean so the dishwasher will drain properly. A drain air gap is usually mounted on countertop and can be inspected by removing the...
Este manual também é adequado para os modelos :Máquinas de lavar louça - 1400 (1.25 mb)