Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
To adjust the rack, open up the tabs that lock the guides and pull out the rack. Arrange the rack with the back wheels in either the top or bottom position and then insert it along the guides until the front wheels are on as well. Close the tabs to lock the rack in place (see Fig. F). Fig. A 1 2 3 4Fig. F 5 GB Turning on the Appliance Starting a wash cycle ... After performing all the operations described in the previous paragraphs, turn the water tap on completely and press ONOFF button "A": you will hear a short beep and indicator light "B" lights up. Now the appliance is on and ready to be programmed. Selecting a wash cycle … To select the wash cycle, turn knob "D" clockwise until the reference notch on the knob corresponds with the number or symbol for the cycle you wish to set (have a look at the wash cycle table on page 7). For a few seconds, the indicator light "G" concerning the pre-wash cycle phase begins to flash, then it stays permanently on without flashing for another 10 seconds approximately. During this time, you can modify your choice of wash cycle. A short beep will indicate the start of the wash cycle and indicator light "G" corresponding to the cycle starting phase will light up. After a few seconds, you will hear a short beep: the wash cycle has begun and we do not recommend you change it. Cycle phase indicator lights The dishwasher is provided with 4 indicator lights "G" which come on in sequence as the appliance is performing that specific phase of the wash cycle. These phases are: pre-wash, wash, rinses, drying Cancelling or modifying a wash cycle in progress….. You can modify the wash cycle in progress, if it has only just started. Turn the knob anti-clockwise until it reaches the Reset position and, after a few seconds, you will hear 4 beeps and indicator light "G" will turn off. This is to inform you that all the settings have been cancelled. You are now free to re-set the correct wash cycle. If you have left out a dish… You can interrupt the wash cycle by pressing the ON-OFF button, insert the dish you had forgotten and press the ONOFF button again. The cycle will start up from where you interrupted it. There's been a power failure? Have you opened the dishwasher door? The wash cycle stops and then restarts when the electricity comes back on or when you shut the door. At the end of the wash cycle…. The end of the wash cycle is indicated by two short beeps and the flashing of the drying phase indicator light. Turn the knob anti-clockwise to Reset in order to reset all the settings. Turn the appliance off to cut off the electricity supply. Turn off the water tap. Wait a few minutes before unloading the dishes: they are very hot! If you wait a little while, they dry better thanks to the steam. Empty the lower rack first. Make sure the wash cycle has ended before removing the dishes! Warning: If opening the door soon after the end of the programme, or during it, stand away from the Dishwasher, to avoid possible injury from hot steam. GB 6 Wash Cycle Table Dishwasher washing guarantees your dishes will be cleaned in a hygienic setting for safer, cleaner results. &\FO. &\FOHVHOHFWLR. &\FOHGHVFULSWLR. 'HWHUJHQ. 5LQVH$L. :DV. LQVWUXFWLRQ. IR. SUHZDV. F\FO. GXUDWLR. ZDV. WROHUDQF. .. Very dirty dishes, Pre-wash with hot water at 40°C pots and pans (not to be used with delicate Extended wash at 65°C. 2 Rinses with cold water JU. . . +HDY\'XW. items). Rinse with hot water at 65°C. Drying. Normally dirty dishes, pots and pans. Standard daily cycle. Pre-wash with cold water. Extended wash at 50°C. Cold Rinse Rinse with hot water at 70°C. Drying. JU. . . 1RUPDO:DV. eco Environmentally-friendly cycle, with low energy consumption levels, suitable for 2 Cold pre-washes Extended wash at 50°C Hot rinse at 65°C . . . (F. normally dirty pans and dishes. Drying Economic, fast cycle to be used to on not very dirty dishes right after they are used. No drying cycle. Short wash at 50°C. Hot rinse at 50°C JU. . 5DSLG:DV. Pre-wash of dishes, pots and pans while waiting for the load to be completed after the subsequent meal. Short cold wash to prevent food residue from drying on the dishes. . 6RD. 7 GB Energy Saving Tips -It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. -Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. -Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. -There is no utility in rinsing dishes, cookware and utensils before placing them in the dishwasher. How to Keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trap...