Assessments - 4, GPA: 3.8
(
)
)
|
Facilidade de uso
• The drain hose, inlet hose and mains cable must not be kinked or crushed when the dishwasher is in position. • The dishwasher must also be screwed on tightly to the work surface or to the adjoining units. This is essential to ensure the dishwasher does not tip. Installation and Connection Instructions Dishwashers That Can Be Integrated (see installation template supplied) 3 The door of the appliance can be fitted with a wooden furniture door with the following dimensions: Width: 591 – 594 mm Thickness: 16 – 24 mm Height: (variable) dependent on – Recess height – Plinth height – The adjustment so that the unit matches the height of the adjoining units The exact height of the adjoining units must be measured at the place of installation. Weight: max. 8 kg Installation and Connection Instructions Connecting the Dishwasher Water Connection The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations. • The dishwasher can be connected to cold and hot water supplies up to max. 60 °C. •The dishwasher must not be connected to open hot water appliances or instantaneous water heaters. Permitted water pressure Lowest permitted water pressure: Consult your installer if the water pres1 bar (=10 N/cm2 =100 kPa) sure is less than 1 bar. Highest permitted water pressure: In the case of a water pressure greater 10 bar (=100 N/cm2 =1 MPa) than 10 bar, a pressure reduction valve must be used (available from your dealer). Connect the inlet hose 1 The water inlet hose must not be kinked, crushed or entangled when it is being connected up. 0 Connect the threaded hose fitting (ISO 228-1:2000) on the water inlet hose to a tap with an external thread (. inch). The inlet hose is equipped either with a plastic or with a metal connection nut: – Tighten plastic hose connection nuts by hand only. – Metal hose connection nuts must be tightened using an appropriate tool. Finally, visually check that it is water-tight (ensure that the tap is not dripping). 3 • In order that access to the tap in the kitchen is not limited by the use of the dishwasher, we recommend the installation of an additional tap, or fitting a two way adapter to the existing tap. • If you need a longer water inlet hose than that supplied, VDE approved complete hose sets are to be used. These are available from your local Service Force Centre. Installation and Connection Instructions 3 The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap: Water inlet hose with safety valve After connecting the double-walled water inlet hose, the safety valve is next to the tap. Therefore the water inlet hose is only under pressure while the water is running. If the water inlet hose starts to leak during this operation, the safety valve cuts off the running water and the draining pump in the dishwasher is switched on. 1 Please take care when installing the water inlet hose: – The distance between the bottom edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm: – The electrical cable for the safety valve is in the double-walled water inlet hose. Do not immerse the water inlet hose or the safety valve in water. – If the water inlet hose or the safety valve is damaged, remove the mains plug immediately. – A water inlet hose with safety valve must only be replaced by a specialist or Customer Services. – Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve. Installation and Connection Instructions Water drain Drain hose 1 The drain hose must not be kinked, crushed or entangled. • Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height 40 cm above the lower edge of the machine. Extension hoses • Extension hoses are available from your dealer or customer service. The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded. • Extension hoses may be laid a maximum of 3 metres horizontally; the maximum permitted height for the connection for the drain hose is then 85 cm. Sink outlet connection • The outlet of the drain hose (o 19 mm) fits all commonly available sink outlet spigot types. The outer diameter of the spigot connection must be at least 15 mm. • The drain hose must be fixed to the sink outlet connection using the hose clamp supplied. If the dishwasher is fitted at a high position If the dishwasher is installed at a high level, and the drainhose connection is less than 30 cm from the bottom of the appliance, adapter kit ET 111099520 must be fitted. This is available from Customer Service. Water drain into wash basins (only possible with free-standing appliances) In the case that you wish to hang the drain hose in a wash basin, use a detachable hose elbow. You can obtain this from AEG customer service under spare part number ET 6...