Assessments - 3, GPA: 4.3
(
)
)
|
Facilidade de uso
6. Once the hardness setting is correctly adjusted, press the ON/OFF switch. The hardness setting is then saved. Filling with Special Salt for the Water Softener 1 Use only special salt intended for dishwashers. Never fill the salt container with different types of salt (e.g. cooking salt) or detergent. This would destroy the water softener. Prior to filling with salt, please check each time that you really do have a packet of special salt in your hand. Fill with special salt: – Before putting the dishwasher into operation for the first time. – When the indicator lamp for special salt (ZOUT; SEL) lights up on the control panel. use special salt. 0 1. Open the door, remove the lower rack. 2. Undo the lid on the salt container by turning it anticlockwise. 3. Only when using for the first time: fill the salt container with water. 4. Place the funnel supplied on the container opening. Fill the container with special salt through the funnel; the capacity of the container is approx. 1.0-1.5 k depending on the grain size. Do not overfill the salt container with special salt. 3 SALESALTSALZSEL Operating Instructions 3 The water expelled by filling the salt container with special salt runs out of the salt container onto the base of the washing compartment. This is not a cause for concern, the water will be pumped out at the start of the next wash programme. 5. Clean any salt remnants on the container opening. 6. Turn the lid clockwise to the stop, otherwise special salt will leak into the wash water, this could lead to poor wash results. To avoid this run a rinse programme after filling the salt container with special salt. This will wash away salt water and any salt crystals that have been spilt. 3 Depending on the size of the salt grains, it can take several hours for the salt to dissolve in the water and for the SALT indicator (ZOUT; SEL) to extinguish. The setting of the water softener and thus the consumption of salt are dependent on the hardness of the local water. Operating Instructions Filling with Rinse Aid Rinse aid ensures that your dishes gleam and are free from spots, and that you glasses are clear. 1 Use only branded rinse aid for dishwashers. Never fill the rinse aid container with any another substance (e.g. concentrated vinegar). This would damage the appliance. Fill with rinse aid: – Prior to using the dishwasher for the first time – When the RINSE AID indicator (NASPOELEN; RINCAGE FINAL) on the control panel is illuminated. The rinse aid compartment is on the inside of the dishwasher door. 0 1. Open the door. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Fill with rinse aid exactly up to the level marked “max”; this corresponds to a quantity of approx. 140 ml. 5. Close the lid and press until it locks into place. 6. Wipe up any spilt rinse aid with a cloth. Otherwise too much foam will be formed during the wash. Operating Instructions Adjusting Rinse Aid Dosing 3 As the dishes are washed rinse aid is released from the dispenser into the wash water. The dose is factory set at 4, and can be adjusted from 1 to 6. Only change the setting if streaks, milky spots or dried on water marks are visible on glasses or crockery. 0 1. Open the door of the dishwasher. 2. Press the rinse aid compartment release button with your finger. 3. Fully open the rinse aid compartment lid. 4. Set the dose level. 5. Close the lid and press until it locks into place. 6. If rinse aid has run out, wipe up with a cloth. Setting the Signal Tone for the End of the Wash Programme You can set whether, in addition to the optical indication of the end of the programme, a signal tone is also to be heard. 0 1. The dishwasher must be switched off. 2. Press the signal tone and water softener buttons simultaneously and keep them pressed. 3. Press the ON/OFF switch. The LED indicators for the signal tone and water softener buttons flash. 4. Press the signal tone button again. The multi-display indicates the current setting: Signal tone switched off b0 Signal tone switched on (factory setting) b1 5. Pressing the signal tone button changes the setting. 6. Once the multi-display indicates the required setting, press the ON/OFF switch. The setting is then saved. Operating Instructions In Daily Use • Is it necessary to refill with special salt or rinse aid? • Load cutlery and dishes into the dishwasher • Fill with dishwasher detergent • Select a wash programme suitable for the cutlery and dishes • Start the wash programme Loading cutlery and dishes 1 Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. For washing in the dishwasher the following cutlery/dishes are not suitable: are of limited suitability: • Cutlery with wooden, horn, • Only wash stoneware in the dishwasher if it china or mother of pearl handles is specifically marked as being dishwasher- safe by the manufacturer. resistant • Plastic items that are not heat • Glaz...