Assessments - 2, GPA: 4.5
(
)
)
|
Facilidade de uso
• The phase indicators of the set programme come on. 6. If you want, you can set the options. 7. Press Start. The programme starts. • Only the indicator of the phase in operation stays on. • The display shows the programme duration that decreases with steps of 1 minute. Starting a programme with delay start 1. Set the programme and the options. 2. Press Delay again and again until the display shows the delay time you want to set (from 1 to 24 hours). • The delay time flashes in the display. • The delay indicator is on. 3. Press Start. The countdown starts. • The display shows the countdown of the delay start that decreases with steps of 1 hour. • The phase indicators of the set programme go off. • When the countdown is completed, the programme starts. – The indicator of the phase in operation comes on. Opening the door while the appliance operates If you open the door, the appliance stops. When you close the door, the appliance continues from the point of interruption. Cancelling the delay start while the countdown operates Press Delay again and again until: • The display shows the programme duration. • The phase indicators come on. • The programme starts. Cancelling the programme Press and hold Delay and Start at the same time until: • All the programme indicators come on. • The display shows two horizontal status bars. Make sure that there is detergent in the detergent dispenser before you start a new programme. At the end of the programme When the programme is completed, the end indicator is on and the display shows 0. 1. Open the appliance door. 2. Press the on/off button to deactivate the appliance. 3. Close the water tap. If you do not press the on/off button, the Auto Off device automatically deactivates the appliance after some minutes. This helps to decrease the energy consumption. • For better drying results, keep the appliance door ajar for some minutes. • Let the dishes become cold before you remove them from the appliance. Hot dishes can be easily damaged. • First remove the items from the lower basket, then from the upper basket. There can be water on the sides and on the door of the appliance. Stainless steel becomes cool more quickly than the dishes. CARE AND CLEANING WARNING! Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. CLEANING THE FILTERS ENGLISH 17 Dirty filters and clogged spray arms decrease the washing results. Make a check regularly and, if necessary, clean them. C C A B A1 A2 1. Turn the filter (A) counterclockwise and remove it. 2. To disassemble the filter (A), pull apart (A1) and (A2). 3. Remove the filter (B). 4. Wash the filters with water. 5. Put the filter (B) to its initial position. Make sure that it assembles correctly under the two guides (C). 6. Assemble the filter (A) and put it into position in filter (B). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance. CLEANING THE SPRAY ARMS Only use neutral detergents. Do not Do not remove the spray arms. If the holes in the spray arms are clog- use abrasive products, abrasive cleaning pads or solvents. ged, remove remaining parts of soil with a thin pointed object. EXTERNAL CLEANING Clean the appliance with a moist soft cloth. TROUBLESHOOTING The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact Service. With some problems, the display shows an alarm code: • - The appliance does not fill with water. • - The appliance does not drain the water. • - The anti-flood device is on. WARNING! Deactivate the appliance before you make the checks. Problem Possible cause Possible solution The programme The mains plug is not con-Connect the mains plug. does not start. nected in the mains socket. The appliance door is open. Close the appliance door. You did not press Start. Press Start. The fuse in the fuse box is damaged. Replace the fuse. The delay start is set. Cancel the delay start or wait for the end of the countdown. The appliance does not fill with water. The water tap is closed. Open the water tap. The water pressure is too low. Contact your local water authority. The water tap is clogged or there is limescale on it. Clean the water tap. The filter in the water inlet Clean the filter. hose is clogged. The water inlet hose has a kink or a bend. Make sure that the position of the hose is correct. The anti-flood device is on. There are water leakages in the appliance. Close the water tap and contact Service. The appliance does The sink spigot is clogged. Clean the sink spigot. not drain the water. The water drain hose has a Make sure that the position kink or a bend. of the hose is correct. After the checks are completed, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact Service. If the display shows other alarm codes, contact Service. ENGLISH 19 THE WASHIN...