Assessments - 5, GPA: 4.2 ( )

Fabricante : Hotpoint Arquivo Tamanho: 546.6 kb Arquivo Nome : Língua de Ensino:

decalcified, so that it can be used in the dishwasher. . The water Softener should be properly adjusted to optimise salt consumption and for best washing results. . In order to ensure that the correct amount of salt is being used to regenerate the water softener, the water hardness adjuster needs to be set accordingly. To set this correctly the hardness of your water needs to be ascertained. Find on the table the level corresponding to the hardness of your water and the required adjustments or contact your local Water company to find the exact water hardness level for your area. . Press and hold the Economy 50° button and set the mains switch 1 to ON, the Salt Indicator light 4 will flash. This shows that the Water Softener programme can now be adjusted. WATER HARDNESS TABLE °dH °fH °Clarke mmol/l Normal Wash 65° Economy Wash 50° Reset Quick Wash 35° 0-6 0-11 0-8 0-1.1 0 7-16 12-29 9-20 1.2-2.9 1 17-21 30-37 21-26 3.0-3.7 2 22-50 38-89 27-62 3.8-8.9 3 After releasing the Economy 50° and Mains Switch buttons, the normal 65° and the Economy 50° light neons will be illuminated, showing that the factory set value is 2 (see table below). The Salt Indicator light will continue to flash until the setting is chosen. . To change the setting: Press the Economy 50° button. Each depression of the button increases the set value by one (0-3). If the Normal 65° button, Economy 50° button and the Quick Wash 35° button illuminate the maximum hardness value has been reached. See the table below. After reaching 3, the display starts at 0 again (none of the 3 buttons will be illuminated). . Switch off the Mains Switch 1 . The set value is stored in the appliance. Approx. 4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. 9 Page 10 FP105-01 DWF35/34/33/30 12/02/2002 10:23 am DWF35 & Before Using your Appliance... DWF34 only ADJUSTING THE WATER SOFTENER... . In order to rinse dishes and glasses satisfactorily, the dishwasher requires soft water i.e containing little or no lime, otherwise water stains are left behind on crockery and glasses etc. If the tap water exceeds a certain level of hardness, it must be softened, ie. decalcified, so that it can be used in the dishwasher. . The water Softener should be properly adjusted to optimise salt consumption and for best washing results. . In order to ensure that the correct amount of salt is being used to regenerate the water softener, the water hardness adjuster needs to be set accordingly. To set this correctly the hardness of your water needs to be ascertained. Find on the table the level corresponding to the hardness of your water and the required adjustments or contact your local Water company to find the exact water hardness level for your area. Water hardness table: Models DWF35 and DWF34 only. °dH °fH °Clarke mmol/l To change the setting: -Press the Economy 50° button 3 . Every time the button is pressed, the figure increases by one. After reaching 7, the display starts at 0again. -Set the mains switch 1 to OFF. The new setting is stored in the appliances memory. Approx. 4 litres of water are required for regenerating the water softening system. The overall water consumption per load can therefore be increased by between 0 and a maximum of 4 litres according to the water hardness setting. 0 - 6 0 -11 0 - 8 0 -1.1 7 - 8 12-15 9 -10 1.2-1.4 9 -10 16-17 11-12 1.5-1.8 11-12 18-21 13-15 1.9-2.1 13-16 22-29 16-20 2.2-2.9 17-21 30-37 21-26 3.0-3.7 22-30 38-54 27-38 3.8-5.4 31-50 55-89 39-62 5.5-8.9 -Press and hold the Economy 50° button and set the mains switch 1 to ON, before releasing the programme button again. The indicator light for the Economy 50° button flashes, as does the figure 4 in the numerical display. The latter represents the value that was pre-set in the factory. 10 0 1 2 3 4 5 6 7 Page 11 FP105-01 DWF35/34/33/30 12/02/2002 10:23 am FILLING THE SPECIAL SALT CONTAINER... Note: Only use recommended Dishwasher salt or granular salt. DO NOT use everyday table salt, cooking salt or road salt as they contain insoluble substances which could harm the Dishwasher. How the salt works: While washing is taking place, salt is automatically rinsed out of the salt container into the water softener where it dissolves the lime in the water. The dissolved lime is pumped out of the dishwasher. The water softener system is then ready for the next load. This process of regeneration can only function when the salt is dissolved in water. . You should fill just before starting the programme. . Unscrew the lid of the salt container. Before using the dishwasher for the first time, pour approximately 1 litre of water into the salt container. . Use the supplied funnel to fill salt to the top of the container (maximum of 1.5kg). As you tip in the salt some of the water is displaced and drains away. When you have done this, clea...

Baixe o seu

Para fazer o download, introduza 2 dígitos :