Assessments - 0, GPA: 0
(
)
)
|
Facilidade de uso
The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) 1. Close the door. 2. Switch on ON/OFF switch (. The Cleaning display )* flashes. 3. Press and hold down the START button @. 4. Rotate programme selector 8 until the “Check water supply” display h flashes. 5. Release button. To change the setting: 1. By rotating the programme selector 8, you can switch on intensive drying (Dry display )" is lit) or switch off intensive drying (Dry display )" is not lit). 2. Press START button @. The setting is saved. en Cleaning and maintenance 2 Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine . Check spray arm for grease and limescale deposits. If you find such deposits: . Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. . To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid. . If the appliance is switched off for a prolonged period, leave the door ajar to prevent the formation of an unpleasant odour. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a Warning – Health hazard Never use other domestic detergents, e.g. containing chlorine! Special salt and rinse aid . Check the refill indicators ` and X. If required, refill salt and/or rinse aid. Cleaning and maintenance en Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arm 1:. 3. Remove the lower spray arm 1B upwards. 3.Remove any residue and clean filters under running water. 4.Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. 4.Clean spray arms under running water. 5.Re-engage or screw on spray arms. 8.Install filters. 9.Re-insert baskets. en Fault, what to do? 3 Fault, what to do? Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Operating the appliance”) a Warning – Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. In this case: 1. First always disconnect the appliance from the power supply. 2. Take out top basket 1" and bottom basket 1b. 3. Remove the filters 1R. 4. Scoop out water, use a sponge if required. 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely. 6. Check impeller wheel and remove any foreign objects. 7. Place cover in the original position and press down until it engages (click). Fault, what to do? en Fault table Fault Cause Remedial action “Check water supply” display h lights up. Supply hose kinked. Tap turned off. Tap jammed or calcified. Filter in the water supply blocked. Install supply hose without kinks. Turn on the tap. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew wa...
Este manual também é adequado para os modelos :Máquinas de lavar louça - DIS4335/18 (1.83 mb)
Máquinas de lavar louça - DIS4335/19 (1.83 mb)